How to Construct a Barbed Wire Fence Across a Creek

Save

Constructing a barbed wire fence over a creek isn't as difficult as you may think. The same basic construction methods for spanning flat ground apply for spanning a waterway. The only differences are in how you reinforce the posts on each side of the creek and filling the gap between the creek and bottom wire.

Things You'll Need

  • Shovel
  • Post hole digger
  • Wood saw
  • Level
  • Two 8-foot by 6-inch round wooden posts
  • 2 bags of concrete
  • Work gloves
  • Wire cutters
  • Barbed wire
  • U-nails
  • Tension wire
  • Cable clamps
  • 2-by-4

Setting the Posts

  • Dig a hole on each side of the creek 3 feet deep and 1 foot in diameter.

  • Mix a bag of concrete for each post hole. Place the post in the hole, and dump in the mixed concrete. As the concrete begins to set, use the level to check that the posts are straight.

  • Let the posts sit overnight before you string the barbed wire.

Stringing the Wire

  • Tie off the sections of wire coming from the fence on land to the creek posts. To tie off the wires, wrap each wire three to five times around the post then back around itself several times. Pull the wires as tightly as possible.

  • Cut several shorter wires (as many as the land part of the fence) for the creek span and add a few feet to the length to tie them off in the same fashion, one wire at a time, post to post. Pull them as tightly as possible while you're tying off to the second post.

  • Hammer two u-nails over each wire's initial wrap on the post, one on each side.

Filling the Gap Between Creek and Fence

  • Wrap the end of the tension cable around the bottom of one post a few inches below the bottom fence wire but not on the ground. Use the cable clamp to secure the end of the tension cable back on itself. String the cable taught to the other post and repeat. Trim the excess cable.

  • Hammer u-nails to the tension cable at each post to hold it in place between the ground and the bottom wire. The tension cable should span the creek just under the bottom fence wire.

  • Loop a piece of barbed wire around the tension cable, and wrap it back around itself several times to secure it. Pull the barbed wire down to the surface of the creek and add an extra foot. Cut the barbed wire there, letting it hang into the water. Repeat this in 1-foot intervals across the tension cable to the other side of the creek.

  • Cut the 2-by-4 to just less than the width of the creek. Wrap the ends of each vertical barbed wire strand around the 2-by-4 about one and a half times and secure them with u-nails. The 2-by-4 should hang just on top of the water, closing the gap.

  • Take one or more strands of barbed wire and weave them horizontally through the vertical wires to prevent animals from squeezing through. If there are gaps near the banks, string more barbed wire from the tension cable to the 2-by-4 to fill them.

Tips & Warnings

  • You will need to clean debris from the 2-by-4 from time to time.
  • If the 2-by-4 isn't heavy enough to stretch the vertical wires taught, wrap a chain around the 2-by-4.
  • Barbed wire can cause serious injury, handle it with care and wear gloves.
  • You will get wet. Make sure you're prepared to stay warm and dry while working in the creek. Wear hip boots or waders and be careful not to tear them on the barbed wire.

Related Searches

References

  • Photo Credit Thinkstock/Comstock/Getty Images serre-cable 4 image by thierry planche from Fotolia.com
Promoted By Zergnet

Comments

You May Also Like

  • How to Build a Rock Fence

    Rock fences (or dry stone walls as they are sometimes called) have been used for centuries all over the world. They are...

  • How to Build a Cinder Block Fence

    Make a professional-looking cinder block fence to protect your privacy and as a barrier to the world. Block noise pollution, protect your...

  • How to Install a Farm Fence

    Farm fences hold livestock of various types. The animals you want to contain and your budget dictate the type of fencing materials...

  • How to Mount Fence Clips

    Fence clips are designed to attach fencing materials to fence posts. The fence clip has to work with the fencing material to...

  • How to Fence Across a Pond

    Building fences can be challenging, especially if the fence must cross water. Don't fret. With a little perserverance, you can successfully build...

  • How to Use Fence T-Bar Clips

    Fence T-bar clips are designed to be used on metal T-bar posts and wire fence including barbed wire. Suitable for use when...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!