How to Test Circuit Board Components

How to Test Circuit Board Components thumbnail
A volt meter is a necessity for testing a circuit board's components

A test of circuit-board components, such as capacitors, resistors, transistors and integrated circuits, can be done to some extent without removing the components from the circuit board. More comprehensive testing can be performed on these components when the component is removed.

Most technicians, though, when attempting to diagnose if a circuit board component is faulty, use a volt meter to measure its input and output voltages.

Things You'll Need

  • Voltmeter
Show More

Instructions

    • 1

      Disconnect the power from the printed circuit board and discharge all inductors and capacitors that may present a safety hazard. Confirm that the circuit board's wiring has been done correctly by examining the physical condition of each of the components on the board. Look for cracked, charred or loose components. Replace any damaged components and rewire any wiring mistakes.

    • 2

      Connect and turn on the power to your circuit board again and measure the voltages on the inputs and outputs of each of the components on the board. Use your voltmeter (see Tips) to check the voltage level of all of components' input and output pins.

    • 3

      Determine, for each voltage level checked, if the voltage level is the right voltage level. Rule out a component as a defective component if all the voltage level inputs and outputs are at the right voltage level.

    • 4

      Turn off the power. Remove a component if all its input pins have the right voltage level but one or more of the output pins is at the wrong output voltage. Turn the power back on. Measure the voltage where the measured components pins once were. Replace a component if the voltage measurements are at the right voltage levels with the component removed.

    • 5

      Measure the voltage levels of the output pins of the component (component B) that connects to the input pins of the first component (component A) checked. Do this if, and only if, component A's input pins have an incorrect voltage level. Find the wiring error if the output voltage measurements of component B's pins are not the same as the input voltage on component A's pins. .

    • 6

      Repeat the procedure in Steps 3, 4 and 5 for each component and its preceding component until all of the faulty components and all of the faulty wiring have been located. Proceed in a systematic backwards fashion from the pin where the first incorrect voltage level is found, checking output pins first than input pins of each preceding component.

Tips & Warnings

  • Use an identical circuit board that you know works to determine the right voltage levels. Compare the measurements on the working circuit board with the voltages on the circuit board you are testing.

  • You will need a volt meter to measure the voltages in your circuit. A voltmeter has two probes, a positive probe and a negative probe. For making measurements, the negative probe must be connected to a ground point on the circuit board. The circut board's ground points can be found if you look at the circuit board's schematic (a drawing of the circuit board.) The ground symbol, a standardized symbol, is most often used to denote the ground points.

  • The voltmeter's positive probe is used to measure the voltages on the components' pins. With the negative probe connected to ground, place the positive probe on the component pin you want to measure and read the result on the voltmeter's display. Consult the voltmeter's manual for specifics on using your voltmeter.

  • If you have not been trained in electronics safety procedures you run a high risk of electric shock or electrocution when working on circuit boards unsupervised. Circuit boards that have large components can be extremely dangerous.

Related Searches

References

Resources

  • Photo Credit The Readout image by Cinneman from Fotolia.com

You May Also Like

  • How to Test Circuit Boards

    How to Test Circuit Boards. A circuit board can contain hundreds, or even thousands of connections. ... A test of circuit-board components,...

  • How to Use a Multimeter on a Circuit Board

    How to Test Circuit Board Components. A test of circuit-board components, such as capacitors, resistors, transistors and integrated circuits, ...

  • How to Check Bad Circuit Boards

    As circuit boards have become more complex, so has checking them for problems. However, many faults can be tracked down by checking...

  • Component Levels of Circuit Board Testing

    Component-level circuit board testing involves individually testing each component on a printed circuit board. The objective is to ensure each component performs...

  • How to Test the Points on a Circuit Board

    The circuit board is an integral component in electrical devices such as stereos, computers and guitar amplifiers. It's responsible for processing electrical...

  • How to Identify Circuit Board Components

    Component Levels of Circuit Board Testing. Component-level circuit board testing involves individually testing each component on a printed circuit board.

  • How to Find Faulty Components on PCB

    Check the circuit board for fuses. ... Replacing a component on a printed circuit board (PCB) may become challenging if proper set...

  • Test Equipment for Circuit Boards

    Every electronics technician, engineer, and hobbyist needs proper electronic test equipment to perform troubleshooting, research and design. Electrical test equipment ...

  • How to Test a PCB Board

    A test of circuit-board components, such as capacitors, resistors, ... How to Test LCD Boards; How to Repair a Burned Electronic Breadboard;...

  • Components of Circuit Boards

    Components of Circuit Boards. Circuit boards comprise a sort of circulatory system inside electronic gadgets. ... How to Test Circuit Board Components.

  • How To Test a Voltage Regulator on a Circuit Board

    A voltage regulator in a circuit generally controls the voltage output at a level needed by other circuit components. Most electronic chips...

  • How to Test a Resistor on a Board

    You cannot see current or voltage in a resistor or circuit, so how can you test a resistor to see if is...

  • The Parts of an LCD Monitor

    There are a variety of components that sync together to create a working monitor power supply board. The main eight component parts...

  • How to Test Printed Circuit Boards

    Building electronics has been made much simpler with the advent of the printed circuit board (PCB). They consist of a silicon board...

  • How to: PCB Electrical Testing

    Every electronic device contains one or more printed circuit boards, or PCBs. As technology is improving and component sizes are getting smaller,...

  • How to Test Which Part Is Shorted in a PCB?

    A PCB, or Printed Circuit Board, contains a large number of electronic components that are interconnected through thin copper traces. The distance...

  • How to Test an Electronics Component

    Testing electronic components is a relatively simple process. There are three primary electronic components in nearly all circuits. The resistor limits the...

  • How to Troubleshoot a Circuit Board Capacitor

    Do not test a powered circuit board unless you know how to work around hazardous voltages. Some circuits, especially those with vacuum...

  • Components in a Circuit Board

    All electronically controlled devices, such as computers and phones, have one or more circuit boards. A circuit board is what holds different...

Related Ads

View Mobile Site