If your woven cane chair broke, repair it instead of replacing the entire chair. When purchasing pre-woven cane to repair your chair, take into account at-home trimming, and order the material approximately 2 inches larger than the chair. Verify your chair has a groove all the way around it. Chairs with groves were not hand-caned and accept pre-woven cane material. Refinish the chair with stain or paint before replacing the woven cane seat. This prevents the stain or paint from accidentally splattering on the cane material.
Things You'll Need
- Utility knife
- Pre-woven cane webbing
- Wooden wedges
- Carpenter's glue
Remove the spline from the old cane on the chair. Break the bond on the spline and the chair by carefully cutting each side of the spline with your utility knife. Remove the spline by prying it away from the chair with your awl.
Remove the cane seating. Scrape excess glue or residue away from the groove in the chair with your utility knife.
Place your new pre-woven cane material in water and soak it until it softens. Lay the softened new pre-woven cane material over the opening in your chair glossy side up. Align the pattern on the pre-woven material parallel to either the front or back edge of the chair. The edge you pick does not matter.
Tap a wooden wedge with your mallet into the center of the back rail grove on your chair. Lightly stretch the cane toward the front rail on the chair with your hands, and wedge it at the center of the rail. Repeat for all four sides of the chair seat.
Tap the pre-woven cane into the groves with your mallet and wedge with a blunt tip. Place the wedge into the grove and tap it with the mallet. Tap the cane into the grove alternating from side-to-side and front-to-back to prevent it from distorting.
Remove the wooden wedges from the chair. Cut off the protruding cane around the grove with your chisel.
Measure a piece of dry spline against the grove on side of the chair and mark the ends of the spline with your pencil. Repeat for each side. Cut the ends of the spline at a 45-degree angle with your chisel. If your seat is rounded, use one piece of spline.
Place carpenter's glue into the groves on the chair. Gently press the spline pieces in place. Tap the spline with your mallet and wooden wedge unit it's flush with the surface of the frame on your chair. Allow the carpenter's glue to dry, approximately 24 hours before continuing onto the next step.
Seal both sides of seat (top and bottom) with lacquer and your paintbrush. Allow to dry thoroughly according to the manufacturer's directions before using the chair.
Tips & Warnings
- Break apart wooden clothes pins to use as wooden wedges.
- "Ortho's: Home Repair Problem Solver"; Robert J. Beckstrom, Sally W. Smith; 1995
- "Reader's Digest; 1001 Do-It-Yourself Hints and Tips"; Reader's Digest Association; 1998
- Photo Credit Hemera Technologies/PhotoObjects.net/Getty Images
How to Recane a Chair
Cane chairs are not only beautiful but they evoke a sense of history and craftsmanship missing from most modern furniture. For years...
How to Replace Rattan or Wicker on a Chair Seat
Rattan, also known as "French Cane" or "wicker," is made of reed and its practical use dates back to biblical times. It...
How to Replace Chair Cane With Fabric
Cane-seat chairs are often found at garage sales with damaged cane. This may make the chair very inexpensive, which is a good...
How to Replace the Bottom of a Ladderback Chair
Ladderback chairs can have multiple options for replacement bottoms. One of the most popular options is a hexagonal patterned caned seat. The...
How to Replace Woven Rocking Chair Seats
A country porch often features the rustic simplicity of a rush-woven rocking chair. This chair invites guests to immediately sit down and...
Ideas for Replacing Rocking Chair Seats
Rocking chairs are comfortable, stylish and often nostalgia-inducing furniture items that many people would rather repair than part with in the event...