Pulling the cord on a lawn mower and having it not function can produce frustration, fear and anger. But with a little investigation, you can figure out exactly what is wrong. The problem may be as simple as clumps of grass keeping the blade from moving or as serious as a rusted piston. There are steps you can take to help you determine how to fix a stuck lawn mower engine. Here are a few guidelines to follow to find a solution.
Things You'll Need
- Spark plug wrench
- Socket set
- Marine fogging oil
- Penetrating oil
Lift up the mower to check that the blade is clear. Most modern lawn mowers are direct drive, meaning that when the blade is unable to turn, the motor also will not turn. Make sure that the blade can spin by removing any obstructions in its path. Pull the starter again. If the engine does not turn over, proceed to Step 2.
Remove the spark plug. Pull on the starter. If the engine turns over, and fuel comes from the spark plug's hole, the engine was hydrolocked. If no liquid comes out and the engine still does not turn over, skip to Step 3. The fuel's emergence means that the carburetor needs repair, or the primer bulb is allowing fuel to leak into the cylinder. Check that when the primer bulb is pushed, you encounter resistance and that it reseals when the bulb is released.
Check the carburetor or diaphragm. If the carburetor has holes, or the rubber is hard and brittle, replace it. If the diaphragm is misshapen, it will not fit the carburetor body properly.
If the engine remains stuck with the spark plug removed, the piston rings also may be rusted to the cylinder walls. Spray a small amount of marine fogging oil into the cylinder and allow it to sit for a few moments before attempting to start again. Try this two or three times, allowing the oil to soak into the rings for a little longer each time. If engine remains stuck, move on to Step 4.
Pour a small amount of penetrating oil, such as Marvel mystery oil, into the cylinder. Allow the oil to set overnight. Attempt to pull the cord again. If the engine turns over, change the oil, then replace the spark plug. If the motor turns over easily but does not start, the piston ring must be replaced to restore compression. This will require motor disassembly.
If penetrating oil does not free the cylinder, the piston is rusted in place. The engine will have to be rebuilt.
Tips & Warnings
- Never pull too hard on the starter cord. This can cause the cord to break or damage the starter.
- Wear gloves when inspecting the blade area under the mower because they can be sharp. Do not allow anyone to pull the starter while under the mower.
- Photo Credit cutting grass image by katja kodba from Fotolia.com
Cracked Engine Block Symptoms
A cracked engine block is a rare, but potentially serious, engine problem that can occur for a variety of reasons. Responsible for...
How to Fix Lawnmower Problems
Lawnmowers are an essential part of taking care of your lawn and making your lawn looking good all summer long. Yet, lawn...
How to Start a Lawn Mower When the Hand Pull Is Stuck
Pull-cord problems are common with lawn mowers. You may be tempted, when you are trying to correct the problem, to try to...
How to Test a Coil or Spark Plug on Lawnmower Engine
There are three main ingredients to starting and operating a lawn mower: air, fuel and spark. While checking for a clogged air...
How to Fix a Broken RC Pull Start
Because it is used so often, the pull start on your RC car is bound to break at some point. Rough pulls...
How to Repair a Lawnmower Primer Bulb
The primer is a small rubber button that injects air into the carburetor that then forces some fuel through the carburetor jet...
The Symptoms of Motors With Stuck Rings
The piston rings fit into horizontal grooves in the pistons. The rings expand against the cylinder wall and seal the combustion chamber....
Causes of Failure With a Connecting Rod
The connecting rod connects the pistons to the crankshaft. It converts the linear motion of the pistons to the rotary motion of...
How to Fix a Jammed Garbage Disposal
Garbage disposals are simple machines--basically a motor and a flywheel with impeller arms that spin and shred whatever they touch. Sometimes, though,...