When installing fence posts, it is vital that you set the posts properly to prevent frost heave. Frost heave is a condition that happens when water freezes in the soil and then the soil thaws out. The resulting pressure literally "heaves" the fence posts out of the ground over time. The best way to prevent frost heave in fence posts is to set them on a drainage bed prior to pouring the concrete. Plan where you want the fence posts and then call the utility companies prior to digging the first hole so they can mark where gas and electrical lines run.
Things You'll Need
- Post hole digger
- Spade shovel
- Pea gravel
- Paint stick
- Concrete mix
- Wheelbarrow (or 5-gallon bucket)
- 4-foot level
- Scrap wood (2x4x6 minimum)
Digging the Hole
Start digging fence post holes at least two-foot deep with a post hole digger. A post hole digger resembles two small spade shovels that are connected together. Avoid digging the hole any deeper than three feet. The deeper the hole, the more stable your fence.
Dig around the initial hole with a spade shovel and make the hole 10 inches in diameter and one foot down. A spade shovel has a rounded tip.
Create a bell shape as you dig the remainder of the hole. When the bottom of the hole is larger in diameter than the top of the hole, the concrete setting is less likely to "push up" out of the soil.
Laying the Drainage Bed
Pour a 3/8-inch deep layer of pea gravel into the bottom of the hole. Pea gravel is small pebbles that provide a firm foundation for the bottom of the post. Larger gravel tends to not allow you to level the top of the gravel enough to level the post.
Spread the pea gravel evenly across the bottom using a paint stick or similar object. When it rains, the water seeps past the post and concrete to the bottom of the post. The pea gravel allows the water to drain from under the post. This function not only prevents frost heave, but also protects the bottom of your fence post from rotting due to water buildup.
Mix the concrete according to the bag directions in a wheelbarrow or five-gallon bucket. Combine the specified amounts of concrete mix with water and stir with a garden hoe until the concrete is a slightly thick, pourable consistency.
Set the Fence Posts
Set the fence post inside the center of the hole. Ask a friend to hold the post steady as you check the levelness. Set a four-foot level on each side of the post to ensure the post is level. Pour another six inches of pea gravel into the hole around the post.
Check the levelness of the post again and brace the post on two sides. Nail boards near the top on two adjoining sides of the post and allow the opposite end of the boards to rest on the ground at a 90-degree angle. Recheck the levelness of the fence post.
Pour the concrete mix into the hole until it is six inches from the top of the hole. Stab the concrete with the spade shovel or a stick to remove any air bubbles. Add more concrete as necessary, but keep the concrete six inches from the soil line.
Allow the concrete to cure for 24 hours, or 48 hours if the outside temperature is below 60 degrees.
Remove the support board braces and fill the top of the hole with soil.
Tips & Warnings
- Rent an auger if you have a large amount of holes to dig.
- Always contact the gas, water and electric companies prior to digging any holes. Accidentally cutting into underground lines can cause disruption in service and bodily injury.
- Photo Credit fence post image by SKYDIVECOP from Fotolia.com
How to Prevent Frost Heave in Concrete Slabs
Frost heave occurs in concrete slabs when water in the soil underneath the concrete freezes, displacing the soil and in turn heaving...
How to Fix Concrete Sidewalk Heaves
Concrete sidewalk heaves result from water flooding beneath the pavement and freezing. The freezing water expands, pushing the pavement upwards, and causing...
How to Install Fence Posts in Minnesota
The technique for installing wooden fence posts is similar no matter where you live. The posts must be plumb, securely seated in...