A motorcycle's brakes are an important part of its design. Improperly adjusted brakes can place a motorcyclist in a dangerous predicament without the ability to safely and effectively slow down. Older-style drum brakes, which use mechanical controls, often require minor adjustments to operate at peak efficiency. Conversely, modern hydraulic brakes are susceptible to air bubbles and condensation buildup within the brake circuit. In most cases, basic adjustments can be performed on both systems using basic hand tools.
Things You'll Need
- Wrench set
- Flat screwdriver
- Clear plastic hose
- Jar or container
- Brake fluid
Adjust the front brake drum. Twist the lock nuts on the drum's cable adjuster and brake rod arm counterclockwise with a wrench to loosen the adjusters. Using a wrench, twist the cable adjuster counterclockwise to tighten the cable tension or clockwise to loosen the tension. Spin the front wheel slightly to test the engagement of the front brake. Adjust the cable until the front brake just begins to slow the front wheel as it spins. Adjust the brake rod arm using a wrench, twisting it counterclockwise to tighten the arm and clockwise to loosen it. Stop when the front brake can effectively stop the front wheel when the brake lever is pulled in. Tighten both lock nuts with a wrench.
Adjust the cable tension at the front brake lever perch. Twist the large round lock nut on the cable adjuster counterclockwise to loosen it. Twist the cable adjuster counterclockwise to tighten the cable tension, loosen the cable by twisting the cable adjuster clockwise. Adjust the cable tension until the brake lever has 1/8-inch of free play before engaging the brake. Twist the lock nut clockwise until it is seated firmly against the brake lever perch.
Adjust the rear brake, using a wrench to loosen the brake rod's lock nut. Twist the wing nut on the end of the brake rod to adjust the brake engagement point. To engage the rear brake earlier, twist the wing nut clockwise. Twist the wing nut counterclockwise to require more effort to engage the rear brake. Tighten the brake rod's lock nut with a wrench once you are satisfied.
Adjust the front brake lever using the rotating adjuster on the lever's pivot. Push the brake lever forward slightly, twist the adjuster to the desired setting and release the lever. Adjust the rear brake pedal, using a wrench to loosen the lock nut on the pedal's threaded adjustment rod. Twist the adjustment rod clockwise to engage the brake earlier and counterclockwise to engage the brake later.
Reset the brake caliper's pistons. Remove the caliper from the motorcycle. Insert a large flat screwdriver into the caliper, between the brake pads, and push the pistons back into the caliper housing. Reinstall the caliper onto the motorcycle and pump the brake pedal or lever repeatedly to rebuild hydraulic pressure and close the piston around the brake rotor. Stop when the lever or pedal requires a firm pull to engage the brake.
Bleed the brake circuit. Attach a length of clear plastic hose to the brake caliper's bleed valve and open the brake master cylinder's fluid reservoir. Place the open end of the hose into a jar or container. Using a wrench, turn the bleed valve clockwise one-quarter turn to open the valve. Pull in the brake lever and hold it in place to force a small amount of brake fluid into the plastic hose. Close the bleed valve, turning it one-quarter turn clockwise with a wrench. Release the brake lever. Refill the master cylinder's reservoir with fresh brake fluid as needed. Repeat as necessary until the brake fluid in the hose is clear and free of bubbles and debris.
Tips & Warnings
- Don't allow the master cylinder reservoir to drain completely. This will allow air into the brake circuit, requiring you to start the process over again.
- "The Professional Motorcycle Repair Program"; Professional Career Development Institute; 1995
- Dan's Motorcycle: Drum Brakes
- Dan's Motorcycle: Hydraulic Brakes & Clutch
- Photo Credit frein image by FrÃ©dÃ©ric Prochasson from Fotolia.com
Adjusting the Front Brakes on Your Harley
Throughout the years, Harley-Davidson motorcycles were equipped with either a drum or hydraulic disc front brake system. The older drum-style setup used...
How to Adjust Drum Brakes
Drum brakes are used only on the rear of some vehicles. Today, many vehicles are being manufactured with four-wheel disc brakes. Vintage...
How to Brake Properly on a Motorcycle
Motorcycles have two brakes - the front operated by the right hand, the rear operated by the right foot - and both...
How to Adjust Disk Brakes on a Motorcycle Scooter
Once the prevailing method for braking, the drum and shoe brakes of yesteryear are gone for the most part. Although effective enough...
How to Adjust a Motorcycle Brake Hand Lever
Motorcycle riders, like their motorcycles, come in different shapes and sizes. To accommodate for riders with smaller hands, many motorcycles offer adjustable...
How to Adjust a Softail Foot Brake
Harley-Davidson Softail motorcycles come in two general brake pedal configurations: adjustable and nonadjustable. As a rule of thumb, Softail motorcycles with forward...
Adjusting Scooter Drum Brakes
Many scooters made and sold today come with a disc brake on the front wheel, which generally involves working with a hydraulic...
How to Tighten the Brakes on a Bicycle
Learn how to tighten the brakes on a bicycle in this expert self help video
How to Adjust Bicycle Front Brakes
Repairing bicycle brakes. Learn how to adjust front brakes on a bike with expert tips on bicycle repair in this free video...
How to Adjust Bike Brakes
Adjusting bike brakes requires the correct tools, and following a few simple steps to make sure your breaks are working as efficiently...