How to Raise Calcium Hardness in a Swimming Pool

Hunker may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.
Maintaining proper calcium hardness is essential to keeping your swimming pool in good working order.

Along with pH and total alkalinity, the third important measurement of water balance in a swimming pool is the amount of dissolved calcium. This measurement is usually called the "hardness" of the water — high calcium levels indicate hard water; low levels are "soft" water. Although there are other dissolved minerals in water, such as magnesium, it is calcium you should be most concerned about. A dissolved calcium level that is too high (hard water) can be damaging to a pool, but a low calcium level (soft water) can also cause problems.

Advertisement

Soft water (low calcium levels) can cause plaster or concrete pool walls to lose their calcium to the pool water, and can cause vinyl pools to lose their elasticity. This can be a very expensive problem, so pool owners need to address low calcium quickly.

Video of the Day

Video of the Day

High levels of calcium, on the other hand, can destroy a filtration system by leaving deposits of scale in the pipes and parts. In certain parts of the U.S., such as the Southwest, hard water is an ongoing problem for pool owners. Simple evaporation of water, which is accelerated in very hot, sunny climates, will gradually concentrate the amount of dissolved sodium in the water, making it harder.

Advertisement

The ideal reading for calcium hardness in pool water is about 200 to 400 parts per million. Fortunately, calcium hardness changes rather slowly, so a once-a-month testing and adjustment should be all you need.

Step 1: Dip the Test Strip

Dip the calcium hardness test strip into the pool water.

Test the water for calcium hardness using a test strip from the calcium hardness test kit. Dip the strip in the water on the deep end of the pool, as far down in the water as you can reach.

Advertisement

Step 2: Read the Results

Compare the test strip to the color chart n the kit.

Remove the strip from the water. Compare the color on the strip to the color chart in the kit. This tells you the hardness level in the water. If the level is below 200 ppm, you need to raise the level. If the level is above 400, skip to step 7.

Advertisement

Step 3: Measure Calcium Chloride

Measure out enough calcium chloride to raise the hardness level. Use 1 1/4 pounds of product per every 10,000 gallons of water if you need to raise the level by 10 ppm. Use 2 1/2 pounds (per 10,000 gallons) to raise the level by 20 ppm, or use 6 1/4 pounds of product (per 10,000 gallons) to raise the hardness level by 50 ppm.

Advertisement

Advertisement

Step 4: Mix the Solution

Mix calcium chloride with water in a bucket

Fill a bucket with warm water. Add the measured amount of powdered calcium chloride to the water in gradual amounts — never add water to the compound. Allow the product to dissolve.

Advertisement

Step 5: Pour the Solution

Start pouring the mixture into the deep end of the pool. Slowly walk around the deep end, pouring in the mixture until it is all gone. Turn on the pool filter, and let it run for at least six hours.

Advertisement

Step 6: Recheck for Hardness

Retest the calcium level the next day. Assuming the level is correct, check the chlorine and alkalinity levels, and adjust them if needed. Return the pool filter to its normal operating schedule.

Advertisement

Step 7: If You Need to Reduce Calcium Hardness

If the calcium level is above 400 ppm, your water is excessively hard, and you'll need to take steps to reduce it. The best way to do this is simply to drain some of the water out of your pool and add fresh water. This effectively dilutes the concentration of calcium in the water, thereby lowering its concentration.

If you are well over the 400 ppm maximum calcium amount, you may need to drain and refill as much as 1/4 of the water in your pool to effectively reduce the calcium hardness back to the middle of the acceptable range.

Advertisement

Advertisement

Report an Issue

screenshot of the current page

Screenshot loading...