How to Install a Woodburning Stove in a Garage

Hunker may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

A garage space is often far more than a place to park a car. It can also serve as a workshop for weekend projects or an activity space for the kids, but it is typically unheated. Adding a small wood stove will improve the space for comfortable year-round use. The safe, basic installation procedure can be adapted to any wood stove and installation preference.

Step 1

Place the stove unit in the desired location in the garage to complete a preliminary measuring for the wall covering and chimney system's ceiling and roof penetration. Consult the manufacturer's specifications for non-combustible wall clearances and make certain the stove position meets or exceeds these requirements.

Advertisement

Video of the Day

Step 2

Mark a line on the ceiling for the chimney opening, using a plumb bob over the center of the chimney connection flange on the stove.

Step 3

Mark a circle to the diameter of the chimney sections that penetrate the ceiling and roof, using a scribing compass. Add 4 inches to the diameter of the hole to allow for a typical minimum clearance to any combustible material, such as ceiling joists or the roof structure. Adjust the stove position or chimney configuration as necessary to keep the chimney's roof penetration as close to centered between roof rafters and ceiling joists as possible.

Advertisement

Step 4

Cut through the ceiling sheetrock, if applicable, using a jab saw or utility knife. Cut the ceiling hole to accommodate the metal chimney collar.

Step 5

Cut the roof sheathing and roofing around the outline of the circle centered on the stove connection, using a jigsaw or reciprocating saw.

Advertisement

Step 6

Clear away the roofing around the opening. Prepare the roof and install the chimney collar flashing, following the chimney manufacturer's instructions. Verify the hole's correct location, using a plumb bob lowered through the ceiling hole.

Step 7

Measure out a space on the concrete floor under the wood stove from the wall line behind the stove to a perpendicular point 18 inches beyond the front edge of the stove's door opening. Use a framing square to align the tape measure.

Advertisement

Step 8

Move the stove unit away to access the rear wall.

Step 9

Cover an unfinished garage wall, one with no sheetrock installed, with a full sheet of fire-rated sheetrock, positioned horizontally and centered, keeping a minimum of 48 inches on each side from the center line of the stove location. Attach to the garage wall with sheetrock screws and a screwdriver. For corner installations, extent the fire-rated sheetrock 48 inches each way from the corner behind the stove.

Advertisement

Advertisement

Step 10

Place a full sheet of cement backer board 36 inches high and centered horizontally with the center line of the stove. Do not extend the cement backer board beyond the end of the fire-rated sheetrock. Attach to the wall framing with cement board screws and a screwdriver at approximately 8 inches apart on each stud.

Step 11

Relocate the wood stove into place and use a tape measure to verify all the required clearances.

Advertisement

Step 12

Connect the chimney sections. Pass the joined chimney assembly through the roof opening and collar flashing, then slide the base of the chimney assembly over the chimney flange on the stove top. Attach the chimney to the stove flange according to the manufacturer's instructions.

Step 13

Attach the counter-flashing, called a "storm collar," over the roof collar flashing. Run a continuous bead of silicone caulking around the perimeter gap between the storm collar's inside edge and the chimney's vertical surface.

Advertisement

Step 14

Install the chimney cap. Make certain the cap snaps fully locked onto the top of the chimney assembly.

Step 15

Open the chimney flue by turning the metal handle on the side of the chimney, typically about 5 or 6 feet above the floor.

Step 16

Light a small newspaper fire in the stove firebox, using matches. Adjust the flue as needed to sustain an even smoke draft up the chimney.

Advertisement

Advertisement

Video of the Day

Report an Issue

screenshot of the current page

Screenshot loading...