How to Cut an Arch Fence Design

Save

Wood privacy fences are typically constructed in a traditional stockade style. Many variations on the theme can be created even from prefab fence panels available from home improvement centers across the country. Marking an even arch on the panels is the key to creating a beautiful custom panel that can set your yard apart from the neighbors. Cutting your panels before installing them is the best way to get your fence to come out right.

Things You'll Need

  • Fence panel
  • String
  • 3 screws
  • Drill
  • Marker
  • Jigsaw with coarse blade
  • Lay your fence panel on a pair of sawhorses. Drive three screws into the face of the panel; one in the center as near the top as possible, and two 8 inches below the top as near each edge as possible. Tie a string around the screw at one edge. Run the string over the screw at the top of the panel and stretch it snugly down to the screw on the opposite edge, and tie it firmly in place. The string should now form a peak like the gable of a roof.

  • Draw the arch along the top of the fence with a marker. Start at one edge and place the marker underneath the string and drag along the string, pushing it up toward the top. This will create a curved line up to the center screw. Draw along the string on the other side of the center screw to complete the arch. Remove the screws and string.

  • Install a coarse tooth jigsaw blade in your jigsaw. Set the saw at the edge of the fence, where the line intersects it. Start the saw and allow the blade to come up to full speed. Start the cut by applying steady pressure to cut along the line. Allow each picket to drop off as it is cut through.

  • Keep the saw moving in a steady arch to get the best cut; stopping and restarting can cause jagged edges. Run the saw just below the marker line to remove all traces of it. To avoid splintering, do not force the saw through the outside of the panel.

  • Sand any unevenness or splintered edges with a belt sander to create a clean, smooth edge. Repeat the marking and cutting process with each panel in your fence. Make sure to get the top screw centered and drop the side screws an even 8 inches to get the curve as close as possible to the same radius.

Related Searches

References

  • Photo Credit electric fret-saw image by Cherry-Merry from Fotolia.com
Promoted By Zergnet

Comments

You May Also Like

  • How to Make an Arch Top Gate

    An attractive yet functional addition to a garden, a gate provides access into the enclosed space, increases privacy and enhances the appeal...

  • How to Build a Wood Gate Arch

    Welcome visitors to your garden with a classic wood gate arch. Gate arches have a long history in gardens and provide an...

  • How to Make a Wire Arch

    Metal wire is not only useful for home improvement but also makes an excellent material for crafters. Metal wire can be used...

  • How to Make a Fence Gate

    To make a fence gate is easy when you use a fence panel from the existing fence. The project takes about an...

  • How to Cut a Convex Design in My Fence

    Wooden privacy and picket fences can be designer-friendly with a convex design so that they do not create a solid horizontal line...

  • How to Scallop a Fence

    Homeowners can scallop a wood fence to create a distinct pattern at the top of the structure. The trade-off is some reduction...

  • How to Make a Curved Fence

    A curved fence may be a bit of a misnomer. The segment of fence between each post is always a straight line...

  • How to Use a Cattle Panel As a Trellis

    Cattle panels, which are flexible wire panels that are usually used to pen in livestock, also made ideal arched garden trellises for...

  • How to Cut an Arch in Wood

    From time to time, a wood project calls for cutting an arch into a piece of wood. At first glance, cutting an...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!