How to Calculate Limit of Detection (LOD)

Save

Analytical instruments are used to detect, quantify and qualify almost everything imaginable. Detection of energy or matter requires a baseline reading (no analyte) and a signal generated by the analyte of interest. Baselines are not perfectly flat-they have mild deviations known as "noise." Limits of detection generally require the analyte signal to be from three to 10 times greater than the "noise" fluctuations.

Things You'll Need

  • Analytical instrument
  • Experimental result
  • Peak height measurement
  • Establish a baseline. Run the analytical instrument in the absence of the analyte to determine the baseline value of the detector. Stable baselines should not drift up or down.

  • Examine the baseline and determine an average value. Use the instrument's integration capability or draw a line through your best-guess at what the average value is between up and down noise. Note the value of the average on the readout scale (y-axis value).

  • Determine the noise. Measure 10 peaks above the average value for your baseline. Add the values together and divide by 10. This is your average noise value. Note: Some instruments have "system" peaks that are predictable and much higher (or lower) than baseline--if you can predict the system peak, it doesn't count in determining noise.

  • Add a standard of known value. Introduce an energy of known value (a sound, light, or electrical input for energy analysis instruments) or a chemical quantity of known value. Start with a high concentration of the standard so you get a good peak in the readout. Note the value (concentration or strength) of the standard and the value of the peak height. Measure from the top of the peak to the baseline.

  • Determine absolute limit of detection. Reduce the concentration or intensity of the standard. Input a smaller signal or concentration until the analyte peak is about three times the height of your average noise peak. This intensity or concentration is the absolute limit of detection.

  • Determine the quantification limit of detection. Increase your input intensity or concentration to the point the peak height is 10 times the average noise peak. This is the lowest concentration for which you can reasonably state the concentration or intensity of the analyte.

Tips & Warnings

  • Any change in chemical or equipment parameters requires recalculation of baseline noise and limits of detection. Some machines require substantial warm-up time before they give an even baseline. Wait until conditions are stable before you figure your limits of detection.
  • Researchers are often tempted to use the absolute limit of detection for the limit of quantification. It gives them more data and makes it seem as if they have a more sensitive protocol-but isn't good science. Be conservative and honest for more robust data and a more solid reputation.
  • Photo Credit Heartbeat image by JASON WINTER from Fotolia.com display of waveforms image by Albert Lozano from Fotolia.com business line graph image by Nicemonkey from Fotolia.com Calculator image by Alhazm Salemi from Fotolia.com Heart beat chart image by Sophia Winters from Fotolia.com
Promoted By Zergnet

Comments

You May Also Like

  • How to Detect Peak in MATLAB

    MATLAB is a technical software package that can be used for signal processing and analysis. A common procedure in signal analysis is...

  • How to Reject Outliers in Data

    Data collected during experiments, surveys and other information gathering procedures is usually subject to some amount of randomness. In some cases, individual...

  • How to Calculate Upper & Lower Control Limits

    Quality control in manufacturing relies heavily on statistics, particularly on the set of statistics that address upper and lower control limits. These...

  • How to To Calculate LOQ

    In clinical biochemistry, analytical and clinical chemistry as well as other science fields, finding the detection limits of materials being analyzed is...

  • How to Calculate 95% Confidence Limits

    Variation in the distribution of a statistical variable is called the measure of dispersion. The standard deviation of a distribution that consists...

  • How to Find a Limit in Calculus

    Calculus is a mathematical discipline that is based on limits. The first lessons in any introduction to calculus course concerns limits, which...

  • Precipitation Titration Techniques

    Precipitation titrations are a form of titration useful in the determination of halides such as chlorides, bromides and iodides. These titrations involve...

Related Searches

Check It Out

Can You Take Advantage Of Student Loan Forgiveness?

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!