Helical gears are spur gears that have their teeth set at an angle with respect to the axial center line of the shaft supporting the gear, instead of parallel to it. They are used in most high-speed automotive and machine applications where quiet operation and high gear loads are key factors. Helical gears have higher sideways thrust loads (axial loads) and slightly lower efficiency than straight spur gears, however, which makes their integrations more costly to build and operate. Calculating thrust loads for helical gears is therefore essential to their proper design and implementation.
Things You'll Need
- Calculator or spreadsheet
Define the helical gear application. In this case, a reduction gear set employing helical gears is used in a luxury inboard boat drive because of its smoothness and quiet operation. Engine torque at cruising speed is 360-foot-pounds. If the pitch diameter of the right-handed 22-tooth driving gear connected to the spinning engine shaft is 4 inches and the diameter of the 44-tooth driven gear connected to the propeller shaft is 8 inches and their helical angle, B, is 18 degrees, you can calculate the axial thrust created by the driven helical gear while the boat is cruising.
Consult a helical gear right-hand, left-hand gear sense diagram to obtain the direction in which the thrust will be directed and a sense for the numbers you will be calculating. In this case, (all looking from the rear of the boat), the engine is rotating counter-clockwise, the propeller shaft is clockwise, the driving gear is helical right-hand, and the driven gear is helical left hand. Therefore, the driven helical gear will impart its thrust to the front of the gear case.
Calculate the instantaneous torque applied to the propeller shaft. Since the smaller 22-tooth gear is driving the larger 44-tooth gear, torque is doubled and speed is halved on the propeller shaft. Therefore, the driving torque applied to the propeller shaft is 360-foot-pounds x 2 = 720-foot-pounds.
Calculate the instantaneous tangential gear force Kt imparted to the teeth on the driven gear. The radius of the driven gear is 8 inches/2 = 4 inches. However, the torque transmitted is 720-foot-pounds. Therefore the torque must be multiplied by 1 foot(12 inches)/4 inches = 3 x 720-foot-pounds = 2160-pounds of tangential force against the gear at the point where its pitch circumference intersects the helical gear mesh.
Calculate the axial thrust on the driven helical gear. The helical gear thrust equation is Ka (axial force) = Kt (tangential force) x tangent of angle B = 2160-pounds x 0.3249 (tangent value of 18-degrees) = 701.82-pounds, directed toward the front of the gear case. This would also be the axial thrust imparted to the smaller driving gear because their respective Kt values are the same, although the direction of the force for the smaller gear would be in the opposite direction, toward the rear of the boat and the common gear case.
Tips & Warnings
- Gear trains, spinning shafts, fans, wheels and belt pulleys of any kind are notorious finger-crushers and necktie trappers—always exercise extreme caution around any open drive mechanism or machinery to avoid serious injury or death.
- Always use protective eyewear around machinery.
- Photo Credit rusty gear on the paper image by Dmitri MIkitenko from Fotolia.com old gearbox dumped in a rest area on the side of the road image by Undy from Fotolia.com gears image by steve dimitriou from Fotolia.com
How to Calculate Axial Stress
Axial stress describes the amount of force per unit of cross-sectional area that acts in the lengthwise direction of a beam or...
How to Calculate Force Impulse on Landing Gear of Aircraft
The fact that aircraft landing gear is termed landing gear and not take-off gear implies that the most critical part of their...
How to Calculate the Axial Load
Axial load is the amount of force exerted in either the vertical or horizontal direction. Though this load may seem straightforward to...
How to Calculate Helical Length
A helix is defined as a spiral that also has a linear dependence upon a third dimension. Found both within nature and...
How to Calculate the Reaction Thrust in a Relief Valve
The reaction thrust on a valve is the force acting on it in the opposite direction of the fluid it expels. The...
How to Calculate Bevel Gears
Bevel gears are used to facilitate gearing where two gear shafts are 90-degrees apart. There are four types of bevel gears: Straight,...
How to Calculate Spur Gears
Spur gears are a simple assembly consisting of a cylinder with teeth projecting outward, and are used to provide standard rotary motion...
What Is the Difference Between Spur & Helical Gears?
Spur and helical gears are two different types of mechanical gears. A spur gear is circular and has its teeth pointing straight...
Examples of Gears and Pulleys
Gears and pulleys are used for many common objects and machines. A gear is "a toothed machine part, such as a wheel...
Helical Gear Advantages
Gears, like all mechanical devices, underwent a series of design evolutions over time. Straight cut, or spur, gears are quick and easy...