How to Install a Hanging Ceiling


Hanging ceilings go by a variety of names, including drop ceilings or suspended ceilings, and these ceilings can offer a variety of advantages. The tiles are suspended or hanging from a metal grid that is attached to the roof structure. The space between the roof and ceiling tiles provides easier soundproofing and fire-resistant properties than traditional ceilings. If you have decided that hanging ceilings are for you, most ceiling companies will offer professional installation. However, experienced do-it-yourselfers may try to perform the task.

Things You'll Need

  • Tape measure
  • Level
  • Pencil
  • Stud finder
  • Perimeter molding
  • Nails
  • Hammer
  • String
  • Suspension wire
  • Wire cutter
  • Runners
  • Utility knife
  • Measure from the current roof structure down the wall 4 inches; this is the minimum distance required between the ceiling and the hanging tiles. If you intend to use recessed lighting, measure at least 6 inches.

  • Trace a line around all walls at the 4 inch mark. Use a level to make sure your lines are straight; you will install a piece of the ceiling grid along this line.

  • Locate the studs along the perimeter line with a stud finder; mark these with a pencil. These will be the spots for nails that will hold your molding in place.

  • Nail perimeter molding in place on all four walls. Line up the top of the molding with your perimeter line and be sure to put nails into the studs. Put molding to the end of the wall and butt it to the molding on the next wall.

  • Stretch string at the perimeter length, along the ceiling joists. Starting at one wall and perpendicular to the joists, measure 4 feet from the wall and hang a string perpendicular to the joists; this is the location for your main tee installation. Continue to measure and mark every 4 feet for a main tee. This string grid will help you visualize the location of your parts.

  • Cut suspension wire 12 inches longer than the distance between the ceiling and the guide wires you just hung. Attach a suspension wire to the ceiling with eye hooks; drill in the hook and then wrap the wire at least three times around to secure it. Install an eye hook and suspension wire every four feet along the main tee lines.

  • Attach runners for the main tees. Line up the first runner with the perimeter molding and attach it to the first suspension wire in its path. You will see small holes along the runner; attach the suspension wire through these holes, wrapping at least three times for security.

  • Continue to install runners all along the main tee lines. If the runners are not long enough to reach the far side of the room, join them together by the slots and tabs on their ends. If you need to join runners together, install an additional suspension wire to support the joint. If runners are too long, clip them off with tin snips.

  • Install cross tee runners by sliding them into the locking slots on the main tee runners; follow exact manufacturer’s instructions for this connection, as the location of the locking slots can vary depending on the product. Install all cross tees, generally 2 feet apart.

  • Cut smaller pieces of runners to join any short runners to the perimeter molding. This is only done if there are small gaps between the runners and molding; this may not apply to every project. Fit the small pieces into place between the main runners and molding; install more suspension wire at these pieces to support them.

  • Install the hanging ceiling tiles or panels by pushing them through the gaps in the grid at an angle and then allowing them to drop into place. If necessary, cut panels with a utility knife to fit in smaller gaps or to work about any fixtures (such as heating ducts). Install all panels to complete the project.

Tips & Warnings

  • Consult with an expert at a ceiling, hardware or home improvement store regarding the design of your ceiling. There are a variety of tile sizes and grid designs to choose from; take accurate measurements, count your ceiling joists and lay out a diagram of your room to make sure have the correct materials needed.
  • Find all materials needed for this project at ceiling specialty stores and hardware or home improvement stores.
  • If your roof structure is not even all the way around, be sure to measure 4 inhes from the lowest point in the ceiling, to make sure you have enough space between the tiles and the roof at all locations.
  • If your perimeter molding is too long for one wall, cut it to size with tin snips. Butt two pieces up against one another for longer walls. If your room features outward-turning corners, cut the ends of both pieces of molding at 45 degree angles and butt them together for a jointed look.
  • Wear safety goggles and protective gloves if you have to cut the runners, molding or panels with tin snips or utility knives. This gear will protect your hands from sharp objects and your eyes from any small pieces of shrapnel that may fly from the cut edges.

Related Searches


  • Photo Credit Goodshoot/Goodshoot/Getty Images
Promoted By Zergnet


You May Also Like

  • How to Hang a Drop Ceiling

    A drop ceiling is good way to cover up an unsightly and damaged ceiling, and it requires very little alteration of your...

  • How to Install Suspended Ceiling Grids

    Hanging drywall for ceilings can be a very difficult and daunting task. A good alternative is doing a suspended ceiling. Areas like...

  • How to Hang a Lamp

    Lamps can be hung from the ceiling in two ways. One is by hanging the lamp from an electric box which is...

  • How to Install 4 X 8 Ceiling Panels

    Acoustical ceiling tiles will insulate, provide noise reduction both in and out of the room, eliminate echos and give your ceiling a...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

Is DIY in your DNA? Become part of our maker community.
Submit Your Work!