How to Mount Hardware for a Clothes Rod

Save

Closet rods are important. A closet rod needs to be strong, well supported, of the correct height to maximize the closet and at the right depth for clothes hangers to hang properly. Most closet rods have a shelf over the rod for additional storage. Installing a closet rod is not hard but it is important to place your rod brackets in good locations so that when your rods are heavy with clothes, they can support the weight.

Things You'll Need

  • Plastic sheeting
  • Painter's tape
  • Wood filler
  • Putty knife
  • Paint
  • Roller and roller pan
  • 2-inch angled brush
  • Stud finder
  • Pencil
  • Tape measure
  • Screws
  • Power screwdriver
  • Closet rod brackets
  • Level
  • Closet rod
  • End cap
  • Open end cap
  • Closet shelf
  • Sanding block
  • Remove everything from the closet. If this closet has been used by someone else in the past it is likely to need a good scrub down and repainting. By painting the closet you seal out old odors such as smoking, grease or sweaty clothes. Place plastic sheeting on the floor and tape the edges with painter's tape. Fill any holes in the wall with wood filler.

  • Paint the closet with a roller and 2-inch angled paintbrush. Use a paint that will not release odors such as a low or no VOC paint. Allow six hours for the paint to dry.

  • Plan your closet. Often the space in a closet can be doubled with double rods. While you will be paying for extra rods and hardware, you will thank yourself from the moment you start using the closet. Use a pencil and lightly mark the height of each closet rod.

  • Move a stud finder along the back and side walls of the closet marking the location of all studs. It is important to screw the closet rod and shelf bracket into a wall stud for rod support.

  • Install your top closet rod bracket first. Screw two long 2-inch screws through the bracket into the wall stud. Make sure the bracket is level. Position the second bracket level with the first no more than 4 feet from the first bracket. Make sure a shelf placed across the top of the brackets will be level and screw this bracket into the wall stud.

  • Measure from wall to wall or the length of the closet rod. From wall to wall subtract 1/2 inch for hardware dimensions. Cut your closet rod with a table saw. Place your closet rod on the closet rod hanger. Position the enclosed end cap hardware on one end and mark your screw holes. Move the rod aside and screw the cap to the wall.

  • Position the rod inside the cap and across the rod hangers. Slide the open end cap over the end of the rod. Move the rod and mark the screw holes. Screw the cap to the wall with the open side up. Screw the rod to the rod hangers up through the bottom of the rod hanger into the wood. You may need to pre-drill pilot holes if the wood is very hard.

  • Measure and cut the wood for the shelf. Sand along the edges if necessary. Screw the shelf to the bracket by screwing through the bracket from the underside into the wood. Be careful to use screws that will not come through the top of the wood. You may need to pre-drill pilot holes if the shelf wood is very hard. Repeat these steps for each closet rod and shelf.

  • Photo Credit closet image by pearlguy from Fotolia.com
Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Install a Closet Rod

    Instructions for installing the brackets for a wooden or adjustable metal closet rod at the right height and depth.

  • How to Make a Closet Rod

    With all the closet organizers available today, a plain wood rod is sometimes still the best choice, especially for a small closet....

  • How to Make a Clothes Rod With Pipe

    Pipes can be used to make quirky and sturdy clothing rods, lending a quasi industrial style to the closet. Because pipes have...

  • How to Install a Closet Rod on an Angled Wall

    Older houses and those renovated into apartments may not have actual closets, but can include some other funny spaces that can be...

  • DIY Closet Rods

    Closet rods are essential for any closet. Installing a closet rod requires the correct hardware and rod. Measure the length of your...

  • How to Hang Drying Racks From the Ceiling

    Drying racks allow you to hang clothes up to air-dry instead of using a traditional outdoor clothesline or a dryer. Although you...

  • Ways to Hang a Dowel Rod

    Dowel rods come in many sizes and have just as many uses. Smaller-diameter ones can double as nails in glue-and-stick joinery while...

  • Angle Iron Hanger Weight Specifications

    Angle irons are L-shaped metal braces used for a wide range of construction and household functions. Large angle irons often help stabilize...

  • How to Install a Closet Rod

    Installing a closet rod requires cutting the rod to the correct length, choosing a bracket type that will support the weight of...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!