How to Vent a Shed-style Roof

Save

Avoid putting holes in the roof when you don't need to. When the peak of a shed-style roof is at least 18 inches higher than the top of the building's walls you can install vents in the end walls just below the peak. This area is like half of a gable end. If the roof has been installed correctly, this is a non-load bearing location where there is minimal framing to get in the way of a right-triangle vent of your choice. For best results, plan to install one vent on each half-gable end. Install these vents once the sheathing is in place and before the siding is installed.

Things You'll Need

  • Level
  • Speed square
  • Tape measure
  • Circular saw
  • 2-by-4 lumber (optional)
  • Screw gun (optional)
  • 2-inch deck screws (optional)
  • Hammer
  • Roofing nails
  • Determine the pitch of the roof by: using the level to mark a plumb line on the face of a gable-end fascia; placing the pivot point (spot at the base of the right triangle) of a speed square at the bottom of the plumb line with the backside of the right triangle on the plumb line; and reading the pitch where the bottom of the fascia passes through the slot at the bottom of the speed square (common rafter scale).

  • Buy two, right-triangle vents with the same pitch as your roof. Get the correct orientation since one needs to face right while the other faces left.

  • Measure the three sides of one vent, minus the flange or frame, and draw an outline of it on each gable end. Lay this out so the angled side of the vent follows the angled underside of the roof line. Keep the angled line just below the top framing member of the half-gable.

  • Cut out the sheathing inside the lines you drew in step three, using the saw. Set the saw cut depth to match the thickness of the sheathing so you don't cut through any framing. If there are no framing components in the way, or the thickness of the vent will allow you to set the vent in the opening and nail it in place through the flange, then go on to step six.

  • Remove existing framing that will not allow the vent to fit all the way into the opening. Add new framing around the inside of the opening creating a box for the vent to fit into by cutting the two-by-four lumber into lengths that fit between the remaining framing components and fastening them in place with the two-inch deck screws.

  • Apply a bead of silicone caulk all around the back of the flange of each right-triangle vent. Place the vents into the holes and fasten in place by driving nails or screws through the flanges and into the sheathing.

  • Fit the siding to the edges of each vent frame or over the top, depending on your vent type.

Tips & Warnings

  • Right-triangle vents vary in their frame sizes, depths and finish details. Follow the manufacturer's instructions on cutting the holes for the vents you buy.
  • When the building is already sided, consider using a vent that is made for that purpose. These vents may also have separate molding pieces to finish them attractively. You will also need to add framing to the inside of the gable end.
  • Wear eye protection when hammering and cutting.
  • Follow ladder safety guidelines.

References

  • Photo Credit triangle image by Zbigniew Nowak from Fotolia.com
Promoted By Zergnet

Comments

Resources

You May Also Like

  • Types of Roof Vents

    An effective roof ventilation system is essential in equalizing temperatures on both sides of a roof. It keeps your house cooler in...

  • What Is a Gable Vent?

    Most all homes are equipped with multiple vents. You will find them on the underside of your soffits and you will have...

  • How to Shingle the Roof of a Shed

    If you're building a new shed, or refurbishing an old one, you need to pay careful attention to the roof. A well-clad...

  • How to Build a Roof for a Shed

    A simple lean-to style roof can be built on top of a shed with 2 x 6 roof rafters, a plywood deck...

  • How to Build a Slanted Shed Roof

    In order to build a slanted roof, one of your shed's walls must be higher than the other. If the shed walls...

  • How to Vent a House Roof

    A properly vented roof is vital to the performance of the insulation and the roofing system itself. An improperly or inadequately vented...

  • How to Vent a Shed Roof

    Venting a shed is a good way to get proper air circulation and help the air flow in general. There are a...

  • How to Vent a Shed

    Storage sheds make ideal spaces to hold landscaping and lawn grooming equipment. But they are usually stuffy, hot spaces, making them unpleasant...

  • The Best Way to Vent a Roof

    The best way to vent a roof is to get a balance between the exhaust vents and intake vents. Exhaust vents are...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!