Mahogany is one of the most common hardwoods in use. It's easy to work with because of its soft, straight grain and consistent quality. As these characteristics serve it well when building, they can also detract when it comes to finishing. The grain tends to splinter, peel away and scratch. There are many kinds of mahogany but the most popular is Luan, or "Philippine," mahogany. It's a light gray, very straight, somewhat characterless wood. But you can bring it to life if you know how to finish it properly.
Things You'll Need
- Hand-sanding block
- Putty knife
- Wood putty
- 100-grit sandpaper
- 180-grit sandpaper
- 400-grit sandpaper
- Old cotton T-shirt
- Danish oil light walnut stain
- Aerosol clear satin sheen lacquer
Set up two sawhorses in a garage or well-ventilated area. Cover any surrounding areas with drop cloths to prevent making a mess. Make sure the temperature is between 60 and 90 degrees F.
Examine the mahogany for any nicks or gouges. If you find gouges, putty them. Cut a piece of 100-grit sandpaper and place it on the sanding block. Hand sand the wood using steady strokes with the grain for approximately five to 10 minutes. Take off the 100-grit paper and replace it with 180-grit paper. Sand for another five minutes. Hold the piece up to the light, sighting across the surface while tilting it back and forth letting the light reflect off the surface. If you observe any scratches, sand and check again.
Dust off the mahogany by blowing across it. Don't use cloth to dust it; cloth will leave invisible fibers that will show in the final finish. Pour a small amount of the Danish oil stain on the cloth and immediately rub the mahogany with it. If it doesn't cover the entire surface pour more stain on the cloth until the surface is saturated with the stain. Continue to rub the mahogany with the cloth, turning the cloth over and over until the wet look is gone from the mahogany and it's evenly stained. Let dry overnight.
Shake the aerosol can of lacquer for one minute. Holding the can 12 to 14 inches from the mahogany, press the button and make steady passes over the mahogany until a wet sheen of lacquer is consistent over the surface without any streaks or dry spots, but try not to get the coat of lacquer too heavy. Use just enough to cover the surface evenly. Let dry for 15 to 20 minutes.
Fold the 400-grit sandpaper in half and gently sand over the dry lacquer with the grain for approximately two minutes. Dust off by blowing lightly on it. Pick up the can of lacquer and using steady even strokes, spray the surface of the mahogany again, covering it evenly and leaving no dry spots. Let dry overnight.
- Photo Credit staining window frame image by Richard J Thompson from Fotolia.com
Mahogany Vs. Cherry Wood
Cherry and mahogany both have a reddish tint, and to the untrained eye, they appear similar. But look closer, and you'll notice...
How to Create a Faux Mahogany Finish
Once you learn how to create a faux mahogany finish, you'll be able to make an inexpensive piece of unfinished furniture look...
How to Finish Mahogany with Tung Oil
Finishing mahogany with tung oil protects the wood and keeps it from soaking up stains. If you are going to do any...
How to Stain Mahogany Wood
Mahogany is an open-grained wood similar to oak and walnut. A smooth, flat finish requires the grain to be sealed with a...
How to Use Luan Plywood Instead of Cherry
Many woodworking plans and projects call for cherry plywood. The veneer used to create cherry plywood and Medium Density Fibercore, or MDF...
How to Finish Pine With a Mahogany Finish
Pine adapts to mahogany stain nicely. Both woods have similar grain patterns, and pine has a slightly amber color that lends itself...
Sanding Wood Furniture
Wood such as Mahogany needs to be sanded prior to staining. Learn how to sand and clean wood prior to staining in...
Mahogany Wood Treatment
Mahogany is the name for various species of straight-grain, dark hardwood with a reddish-brown cast that darkens over time. Today, mahogany comes...