Toy boats are an easy craft to make in a single afternoon. Wooden boat designs can be modified to make the same craft with cardboard. Sailboats are more difficult to create than flatboats due to the need for balancing the weight of the sails so the boat doesn’t tip over. Cardboard is easy to decorate with markers and paint before sailing. Cardboard boats can be used repeatedly when carefully waterproofed.
Things You'll Need
- Simple rubber-band boat diagram
- Cardboard sheets
- Markers or paint
- Saran wrap
- Aluminum foil
- Rubber band
Easy Cardboard Toy Boat
Cut out two cardboard rectangles 8 inches long and 4 ½ inches side. Lay the first cardboard rectangle on a flat surface with the short end facing you. Measure in 1 inch from the left edge and mark with a pen. Repeat with the right edge. Measure up 2 ½ inches from the bottom and mark with a pen. Use a ruler to draw a straight line between the marks to create a square measuring 2 ½ inches on each side. Cut out the square. There should be a one-inch flap on the right and another on the left side of the cardboard sheet.
On the same piece of cardboard measure 4 inches up from the bottom of the cardboard sheet along the left edge and mark the spot with an X with a pen. Set the compass for a 4½-inch radius. Place the point of the compass on the X at the edge of the cardboard. Draw an arc across the opposite side and toward the top of the cardboard with the pencil end of the compass. Repeat the process on the other edge of the cardboard to create two arcs that intersect near the top of the cardboard. Cut along the arcs to create the bow of the boat.
Place the first cardboard piece on top of the second and trace the boat shape onto the second piece of cardboard. Cut out the second piece of cardboard. Cut two strips of cardboard 8 inches long and 1 inch wide. Cut two small sqaures, each 1 inch long and 1 inch wide. Cut three cardboard strips 2 ½ inches long and 1 inch wide. Cut a cardboard strip 3 inches long and 1 inch wide. Use markers or paint to decorate the cardboard pieces before continuing.
Set one boat template on a flat surface with the bow facing away from you. Stand one of the 8-inch-long cardboard strips on top of the long edge of the boat and tape in place. Repeat with the other 8-inch strip of cardboard on the other long edge of the boat. Add tape around the bow to hold the two strips firmly together. Stand the 1-inch strips along the back of the flaps on the boat and tape in place. Apply the 2-½ inch strips around the square insert of the boat and tape in place. Apply tape at each corner to add strength. When all sides have been put in place add glue along the seam around the inside of the boat. Set aside to dry.
Set the second boat template on top of a piece of plastic wrap that is at least 10 inches long and 6 inches wide. Measure 1½ inches out from each edge of the template and mark with a pen. Cut the plastic wrap out along these marks to create a boat shape that is larger than the template. Wrap the plastic wrap up and around the cardboard bottom and sides of the boat, wrapping the edges into the inside of the boat. Cut a second piece of plastic wrap ½ inch larger than the boat template and wrap it around the other cardboard piece that will make the top of the boat. Glue plastic wrap in place as necessary. Set the 3-by-1-inch piece of cardboard on a sheet of aluminum foil. This piece will be the paddle. Cut a piece of aluminum foil large enough to cover the paddle twice. Cover the paddle with the aluminum foil and glue the edges of the foil shut to seal them.
Apply glue along the top of the walls of the boat and set the second cardboard boat template on top. Press in place. Allow the glue to dry completely. Stretch the rubber band across the back of the boat without twisting it. Insert the paddle between the flaps of the boat and between the rubber band edges. Turn the paddle to make the rubber band twist on either side of the paddle. Set the boat in the water and release the paddle. The rubber band will unwind, and the boat will move forward.
Tips & Warnings
- The paddle should be light enough to float rather than sink when it has finished spinning.
- Photo Credit Boat in Sink image by Hedgehog from Fotolia.com
How to Make Cardboard Boats Float on Water
Floating in a cardboard boat is an inexpensive way to have fun on the water. The materials are cheap and readily available...
How to Make a Cardboard Boat
Playhouses offer children a wonderful outlet for creativity and imagination. This cardboard tugboat welcomes kids aboard on an adventure to explore the...
How to Make a Viking Longship Model Out of Paper
Vikings were Scandinavian warriors, also called Northmen and Norsemen. During the 9th through the 11th centuries, they raided and pillaged northern European...
How to Make a Model Boat That Floats
Model boat kits are widely available at hobby and craft stores. Many of these are scale models of existing craft such as...
Sponge Boat: Decorating
For the sponge boat, decorate with permanent marker, the toothpick and some cloth for a flag. Decorate a sponge boat with tips...