How to Cut 4-by-6 Fence Posts

Save

One challenge to building a large wooden fence is getting the tops of the posts even with each other. You can't cut them to size ahead of time, because the process of setting them in concrete causes height variation. You should set the posts with 6 inches of extra space on top, then cut them all even before you install the fence panels. A standard circular saw can't get through a whole 4-by-6 fence post in one cut, but a makeshift ``jig'' of scrap wood will allow you to cut all four sides exactly even.

Things You'll Need

  • 4-by-6 fence posts, set in place
  • Tape measure
  • Pencil
  • Chalk snapline
  • Tri-square
  • 4 small scrap pieces of 1-by-4 boards, 4 or 5 inches long
  • Screwgun
  • 1 1/2 inch thin wood screws
  • Circular saw
  • Determine the height at which you want the tops of the posts to be cut off. Measure and mark that height at the two end posts.

  • Stretch your chalk snapline between the two end posts, so the string crosses each of the posts in between. Snap the line.

  • At the first post, use a tri-square and pencil to extend the horizontal chalk line from the one marked side of the 4-by-6 to all four sides.

  • Measure your circular saw, from the blade to the far side of the plate (the part that sits flat on whatever you're cutting). Then measure down from the chalk line on the post at that distance, and make a mark. Extend the mark around all four sides of the post, using your tri-square and pencil. You should end up with two parallel sets of horizontal lines going all around the post, at the same distance from each other as the width of your circular saw plate.

  • Set a piece of scrap 1-by-4 underneath the bottom line on one side of the post, so the edge of the board lines up with the line. Use your screwgun to sink two wood screws into the board to hold it in place. Repeat for each side of the post, so you have four scrap boards set up under the bottom lines.

  • Run your circular saw sideways along each side of the post, with the edge of the saw plate resting on the side of the scrap wood and the blade on the top line. The top piece of the post should fall off after the fourth side is cut.

  • Remove the scrap wood from the post, using your screwgun. Repeat the process for each post.

Tips & Warnings

  • Wear eye protection when using your circular saw.

References

  • Photo Credit Jupiterimages/Creatas/Getty Images
Promoted By Zergnet

Comments

You May Also Like

  • How to Cut Wood Posts

    Making a perfect cut on a 4-inch-square wood post, requires perfect alignment of a circular saw blade. If your cut if off...

  • How to Cut Steel Posts

    Cutting steel posts to length is an easy process with the proper tools. No matter what tools you use to make the...

  • How to Cut Cedar Trees to Use As Fence Posts

    Because of their natural resistance to rot and decay, both western red cedar and northern white cedar have long been used for...

  • How to Level Fence Posts

    An uneven fence is not aesthetically pleasing. It's not difficult to level a fence if a few precautionary steps are taken. With...

  • How to Cut 4X4 Fence Deck Posts

    Posts that measure 4-by-4-inches commonly are used in the construction of many different outdoor projects, including decks and fences. The posts are...

  • How to Cut Chain Link Fence Posts

    Chain link fence posts are made out of galvanized steel. Galvanized steel does not rust and thus makes great fence posts. The...

  • The Best Way to Cut 6X6 Deck Posts

    An outdoor deck adds value to your home and makes it possible to enjoy the outdoors more. If you are building your...

  • How to Cut a Mortise in a Fence Post

    One of the tidiest and strongest ways of securing the horizontal rails to a fence post is to mortise the rails. A...

  • How to Cut Through a Metal Fence

    Metal fences are used to protect and provide safety to residential and commercial lots. Metal fence types include chain link with post,...

  • How to Build a Cap & Trim Fence

    Flat top fences lack much in the way of design detail. Adding cap and trim to a flat top panel is a...

  • Homemade Fence Post Caps

    There are many reasons to build a fence. Among the considerations are aesthetics, privacy, durability and cost. Of all the different materials...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!