The low-pressure switch in your car or light truck's air conditioning system is used to interrupt power to the compressor when the low side pressure drops below 25 psi. This prevents freeze-up of the system and possible damage to the compressor. When the switch is faulty, the symptoms of freeze-up, or no compressor function, will be present. Replacement is straightforward, but requires the removal of refrigerant from the system.
Things You'll Need
- A/C gauge set
- Vacuum pump
- Low-pressure switch
Recover the refrigerant in the system. The equipment to perform this task is expensive.Your local auto repair shop will be happy to recover the refrigerant for you, for a small fee. The release of air conditioning refrigerant into the atmosphere is believed to be a factor in the production of green house gases, and a possible cause of ozone layer depletion. Release of refrigerant is prohibited by section 609 of the Federal Clean Air Act.
Refer to your service manual to help you locate the low-pressure switch. Unscrew the old low-pressure switch, and screw the new switch onto the fitting. Replace the rubber o-ring seal with the new one supplied with the new low-pressure switch.
Attach the air conditioning gauge set to the service ports of the air conditioning system, and attach the vacuum pump to the service hose on the gauge set. Turn the vacuum pump on and open the service valves on the gauge set. Allow the pump to run for 1 hour to remove all moisture from the system.
Close the service valves on the gauge set, and disconnect the vacuum pump. Install the can tap that is supplied with the gauge set, and attach a can of refrigerant to the can tap.
Open the can, and open the blue service valve on the gauge set. Allow the pressure from the can to partially fill the system, and then start the vehicle and set the controls to Max A/C.
When the first can is empty, close the service valve, attach another can to the tap, and open the valve to install that can. Repeat this step until the system is full. Refer to your service manual for system capacity specifications.
Close all valves on the gauge set, turn off the engine and disconnect the gauge set from the vehicle.
Tips & Warnings
- Use refrigerant that has dye in it. This helps find leaks if they occur.
- Never open the red high-pressure service valve on the gauge set when the engine is running. The pressure developed on that side of the system will blow the refrigerant can apart, and injury could result.
- Photo Credit Jupiterimages/Photos.com/Getty Images
Definition of a Pressure Switch
A pressure switch is very important little device that enables the safety and control of many different environments. It functions as a...
Car AC Pressure Switch Testing
Auto air conditioning pressure switch testing allows you to diagnose potential or existing AC problems. Pressure testing the vehicle's low and high...
How to Install a Pressure Switch on an Air Compressor
Most air compressors are controlled by a pressure switch. The switch turns the power on and off to the compressor motor. In...
How to Replace a Dodge Neon Air Conditioning Compressor
A compressor is the part of an air conditioner that compacts the fluid to give it more energy. If the compressor is...
How to Test a HVAC Pressure Switch
An HVAC pressure switch is a protective device that is installed in both heating and cooling systems. The switch will open and...
How to Find the Low-Pressure Side of an AC Unit on a Car
The air conditioner on a car is designed as a closed, pressurized system. The system consists of a high-pressure and a low-pressure...
Automotive Air Conditioner Pressure Switch Troubleshooting
An automotive air conditioner's pressure switch cycles the vehicle's compressor on and off when the refrigerant pressure falls below an acceptable level....
How to Replace the A/C Pressure Switch on a Chevrolet Truck
The Chevrolet truck uses two air conditioning pressure switches: a high- and low-pressure switch. The high-pressure switch is designed to shut down...
How to Test a Low Pressure Switch
Low air pressure switches are useful and serve various purposes in the house. These switches can be found on devices such as...
How to Adjust a Johnson Controls Low Pressure Switch
Johnson Controls low pressure switches are used for low-pressure cut-out control, pump-down control, and capacity control on commercial air-conditioning and refrigeration projects....
How to Test an AC Pressure Sensor
Air conditioning pressure sensors, also known as AC switches, turn off a car's air conditioning system whenever the refrigerant pressure reaches a...