Boat motor cooling systems work by drawing water into the lower unit of the motor using its impeller pump. Water is circulated through a system of ports and passages and then out the water exhaust port carrying with it excess heat. Boat motors can be damaged if salt and silt are not flushed from the cooling system. Flushing a boat motor can be accomplished hooking a garden hose to a flushing device which directs fresh water into the motor's cooling system intake. The motor's impeller pump circulates the fresh water through the cooling system and out the water exhaust port along with harmful salt and silt. The most common flushing device, known as 'ear muffs', consists of two rubber cuffs connected by a U-shaped soft steel bracket which can be bent for a better fit. One of the cuffs has a fitting to which an ordinary garden hose can be attached. Some newer motors have a flushing attachment built in. Refer to your owner's manual for instructions.
Things You'll Need
- Boat motor flushing device
- Garden hose
- Access to running fresh water
Attach the flushing device so the cuff with the garden hose is over the cooling system intake port on the lower unit.
Shift the motor into neutral.
Turn on the water about half way. Too much pressure may unseat the flushing device cuffs.
Start the motor and set the throttle to idle.
Check to see that a steady stream of warm water runs from the outlet port. Hot water, water dribbling out, or no water can mean the outlet tube is clogged or the impeller pump is failing. Turn off the motor immediately and unplug the opening or replace the impeller pump.
Sample the cooling water for salt by tasting. Insure thorough flushing by running the water for a minute after the flush water is no longer salty or is clean and free of silt.
Tips & Warnings
- Check the owner's manual for directions specific to your motor. Some manufacturers recommend the motor be tilted for thorough flushing. For added safety the propeller can be removed.
- Be certain the motor shift lever is set to neutral before starting the motor.
- Shut off the motor immediately if you suspect water is not circulating through the cooling system and the motor is running hot.
How to Hook Up a Fuel Tank to an Outboard Motor
Gasoline-powered outboard motors without built-in fuel tanks must be connected to a remote fuel source. Many outboard manufacturers sell fuel tanks and...
How to Flush a Boat Engine
Every time you pull a boat out of the water, you need to flush the engine as part of regular boat maintenance....
How to Attach a Water-Ski Rope to a Boat
One of the last things you want when you water-ski is to watch your ski rope come untied from the boat that's...
How to Flush a Mercury Boat Motor
Every time you bring your boat in, you should flush your Mercury outboard with fresh, clean water to remove aquatic plants, mud,...
How to Use Earmuffs on an Outboard
Marine flush adapters, termed earmuffs in boating circles, allow outboard motors to receive cooling water from a garden hose whenever the motor...
How to Test Jet Boat Engines
Whether you are purchasing a jet boat for the first time or picking up a used boat from a previous owner, checking...
How to Hook Up a Hose Reel
It's advisable to store a garden hose on a hose reel instead of letting it sit on the ground or wrapping it...
How to Run an Outboard Motor Dry
The last thing you want to do is get stranded out on the water with a broken-down outboard motor. That's why after...
How to Hook Up Heater Hoses on Early Engines
The thermostat housed in an engine cooling system blocks the engine cooling system from circulating until the engine reaches a predetermined temperature....
How to Test an Outboard Motor Out of Water
A set of outboard rabbit ears is used to bring water to the intake from your hose to test an outboard while...
How to Run My Inboard Boat in My Driveway
Boat engines rely on a supply of fresh water to prevent overheating. Boats also use water as lubrication for the propeller shaft...
How to Flush an Inboard and Outboard Motor
The purpose of flushing an inboard or an outboard motor is to prevent contaminants from building up inside the engine. Excess salt...
Inboard Motor Maintenance
Boating is an addictive pleasure that makes even the most mundane tasks of the hobby, or lifestyle, absolutely thrilling to perform. One...