How to Make an Infrared Home Sauna

Save

The health benefits of a dry sauna, such as relaxation and detoxifying your body, seem to be maximized when you can use an infrared sauna for deep tissue warming. Building your own infrared sauna is not a complicated project and can cost much less than buying a sauna kit or a prefabricated infrared sauna.

Things You'll Need

  • 2-by-4 lumber
  • 3-inch wood nails or screws
  • Hammer or electric screwdriver
  • 5-inch floor planks
  • Tongue-in-groove pre-cut cedar
  • Pre-made door
  • Pre-made bench
  • Infrared emitter
  • Decide on the location of your sauna and whether it will be freestanding or built into an existing wall. Though infrared saunas utilize dry heat, you will need to ventilate the sauna appropriately.

  • Build a frame for the sauna using 2-by-4s. First, make a floor frame, and attach standard five inch floor planks to cover the floor. Treat the floor only with wood sealant to make it fireproof.

  • Nail upright 2-by-4s every 16 inches along the floor frame to use for attaching the walls later. Starting at the floor, nail the pre-cut tongue-in-groove planks to the wall frames so that they fit from one corner of the wall to the other. Angle the nails in from the top to hide them within the wood and avoid any exposed metal surfaces inside the sauna.

  • Leave a space to frame the door as you build the walls. Check regularly to make sure the wood stays level. After completing all the walls, attach cedar pieces to the upright frame to enclose the ceiling.

  • Hang the door tightly in the door frame. Install the door so that it swings out from the sauna. Install a bench between the walls to complete the interior.

  • Make sure the electrical outlets will support the power needs of the sauna. For a small, one-person sauna, you'll need to support 120 volts. A larger sauna will require 240 volts. Install the infrared emitter on the wall beneath the sauna bench by mounting it to one wall of the sauna in a corner.

  • Place the wires of the emitter through the reflector holes. Clip the emitter to the reflector and screw the wires to the terminal block. Hire a licensed electrician to complete or update the wiring you need for both the infrared emitter and an interior light if you install one.

Tips & Warnings

  • You don't have to insulate an infrared sauna between the frame and the interior walls, but if you do it may increase the energy efficiency of your sauna.
  • Test the sauna before its first use by heating it up for 30 to 45 minutes. Allow it to cool down to make sure the emitter is wired properly and to allow the wood to breathe.

References

Promoted By Zergnet

Comments

You May Also Like

  • How to Build Your Own Sauna Plans

    If you are creating a sauna as a new project or building your very own dream sauna, the options of your sauna...

  • How to Set the Temperature in an Infrared Sauna

    Infrared saunas help users relax in a warm environment, but without the moisture and steam associated with traditional sauna use. Infrared saunas...

  • How to Troubleshoot a Sauna

    Nothing says luxury quite like a sauna in the home. Whether it is a steam or an infrared sauna, the heat from...

  • Far Infrared Vs. Near Infrared

    Infrared waves are part of the range of invisible radiation consisting of wavelengths that range from 750 nanometers to the frequency that...

  • Risks of Infrared Saunas

    Infrared saunas are a modern alternative to traditional steam saunas. Their heating power comes from infrared devices instead of conventional electric heaters...

  • Homemade Saunas

    The joys of a weekly family or individual sauna have been long enjoyed in Scandinavia. Finland, the historical home of saunas, has...

Related Searches

Check It Out

This Is the Beauty Routine of an Ex-Pat in China

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!