A realistic and reusable plaster arm cast can be constructed for theatre productions from materials found around the shop and at hardware and medical supply stores. A little careful engineering is needed to build the cast so it will go on and come off the actor quickly and yet reliably remain on the arm during the entire scene or during action sequences.
Things You'll Need
- Petroleum jelly
- Two white knee-high tube socks
- Rubber glove
- Plaster-impregnated bandages
- Utility scissors
- Mixing Bowls
- Warm Water
- Large, sharp seamstress shears
- White latex paint
- Heavy-duty white Velcro (long strips)
- White, matte finish cloth gaffers tape
Prepare to make a cast on the actor's arm. Cover the arm with petroleum jelly. Slip a cotton knee-high tube sock over the arm. Cut off the toe if necessary.
Dip plaster-impregnated bandage strips into warm water. Let the bandages soak for approximately one minute. Wring out excess water. Wrap the bandages around the arm, just as if building a real arm cast. Make sure the bandages are not wrapped too tightly however: there should be enough room between the bandage and the actor's arm to insert a thick finger up the "sleeve" of the bandage. Do not build a cast up the arm above the bend of the elbow. Continue adding bandages until they form a shell no more than ¼ inch thick. Do not wrap the bandages around the hand or fingers. Do not allow this shell to dry completely.
Cut the cast open. When the bandages have set to a not quite hard state, slide the under-stocking off the arm while holding the cast in position on the arm. Insert seamstress shears, with the tips covered with duct tape, into the wrist end of the cast. Slowly cut the cast open. Make only one long cut. Gently pry the halves of the cast open enough for the actor to withdraw his arm.
Stuff the empty cast with newspaper. Build up the outer surface of the cast with more plaster bandages until the cast is about 1 inch thick. Do not bandage over the cut. Let dry overnight.
Slip a rubber glove over the actor's hand. Make a loose plaster bandage cast around the hand, leaving the fingers and the thumb free. Keep the opening wide around the wrist. When dry to the touch, slip this plaster glove off the actor and let dry.
Smooth any rough edges with wet plaster bandages so they won't chafe the actor. Prime and seal both casts with flat white latex paint and let them dry.
Slip a white tube-sock (with the toe cut off) over the actor's arm. Pry the cast apart widely enough that the actor can slip his arm into the cast along the seam. Attach long strips of heavy-duty white Velcro along the top edge of the cut seam, toothed side down, and another strip of Velcro, with the fuzzy side up, on the other side of the seam. Close the seam with the Velcro. Slip the cast glove over the actor's hand and connect this glove to the cast at the wrist using bands of white matte-finish cloth gaffer's tape.
How to Make Fake Arms & Legs
Whether you’re pulling a prank on a friend or getting ready for Halloween, there are times you’ll want to have a fake...
How to Make a Plaster Cast of an Arm
Making a plaster cast of an arm has a lot of uses. For a doctor, it can be used to fashion a...
How to Waterproof My Child's Arm Cast
There are few things more frustrating, for both parent and child, than the trauma and recovery from a broken arm or leg....
How Can I Make an Arm Cast Smell Better?
Individuals who have been placed into a cast for a broken arm or wrist might inevitably notice the cast begins to smell...
How to Make Fake Crutches
Fake crutches make an excellent accessory to a party costume. Whether you are a going as an injured soldier or a soccer...
How to Tell a Fake Cast Iron Pan
If you take good care of a cast iron pan, your great grandchildren will be able to pass it on to their...
How to Make a Fake Leg Cast
If a fake leg cast is needed for a Halloween costume or a school play, use paper mache. Paper mache replicates the...
How to Make Paper Mache Arm Casts
Casts are the main method that doctors use to immobilize a broken arm. In the past, casts were made of plaster, while...
How to Make a Fake Leg
Whether you are decorating for a Halloween party or making a horror film, you never know when a severed leg might come...
How to Make a Fake Leg Cast Without Fiberglass
Plays and films often feature a character who breaks his leg. It would be inconvenient to encase the actor's leg in a...
Supplies Needed to Make a Fake Arm for Halloween
Learn how to stuff a fake arm for Halloween and what you can use to stuff the arm in this free how-to...
How to Add Fake Blood to Fake Limbs for Halloween
Learn how to add fake blood to fake limbs for Halloween, to give them a more realistic look in this free how-to...