There are two ways to add a bullnose effect to stair treads or steps: routing or molding. The routed edge is the only option for round steps. The molding option includes half-round molding or stair-nose molding on the front of the step. They attach to the front of the step with glue and nails. The routing option imparts the look of fine-woodworking. Half-round and stair-nose are only slightly less elegant and remain mainstays in the building industry.
Things You'll Need
- 5/8-inch round-over bit with bearing
- Medium-grit file
- 100-grit sandpaper
- Hand block
- Half-round molding
- Miter saw
- Stair-nose molding
- Table saw
- Wood glue
- Masking tape
- Finish nailer
- 2-inch finish nails
- Wood filler
- Putty knife
Install a 5/8-inch round-over bit in a router. Place the router base on the front edge of the step on the left side. Adjust the bit up or down so that the center of the cutting edge of the bit is centered on the edge of the step.
Hold the router with both hands and turn it on. Ease the router and bit forward to cut into the edge no more than a quarter-inch deep. Pull the router along the edge to the other side of the step. Don't attempt to round the edge completely in one pass; go easy. The router won't be able to cut into corners; that's fine.
Repeat Step 2 one or two more times as needed, gradually removing more of the edge, rounding it until the bearing rides along the front edge of the step smoothly.
File the edges round where the router will not cut in corners. Use a medium-grit file to shape the edge as much as possible. Finish it off by sanding the edge to match the routed edge with 100-grit sandpaper attached to a hand block.
Measure the length of the step. Cut the half-round -- it's shaped like a D -- or stair-nose molding to the measurement with a miter saw. If the molding has an extended lip along one side of the D shape, it's stair-nose. Measure the distance from the front edge of the step to the riser. The riser is the vertical part that supports the step underneath. Add the thickness of the D shape to the measurement.
Place the stair-nose molding upside down on a table saw with the "D" shape against the fence. Set the fence to the measurement. Rip off the outside edge of the molding to the measurement. Sand the edge lightly to remove rough edges or splinters.
Sand the front edge of the step lightly with the hand block to remove any old finish, dirt or debris. Apply glue under splinters, and tape them down tight with masking tape. Remove the tape when the glue is dry. Sand off the dried glue.
Apply glue to the molding. If the molding has the lip, apply glue to the lip. Apply glue to the front edge of the step.
Place the molding on the front of the step. Stair-nose fits upside down on the step in this instance. The lip fits under the step. Typical stair-nose fits with the lip on top. Shoot one 2-inch finish nail an inch from each corner through the front. Shoot four more finish nails, evenly spaced and centered, through the front of the molding.
Apply wood filler to nail holes, cracks and seams with a putty knife. Sand the seam between the molding and step smooth when the glue and filler is dry.
- Wood Magazine: Router Tips, Jigs and Techniques: Round-Over Bits
- YouTube: Home Remodeling Tools : How to Round Edges With the Handheld Router
- Hardwood Floors Magazine: Contractor Blog: How We Replaced These Winder Stairs
- Popular Mechanics: Room Divider: Installing the Moldings
- Philip Design Lab: Half Round
- Flooring Supply Shop: Installations Staircases and Transitions Molding of Hardwood Floors
- Photo Credit Goodshoot/Goodshoot/Getty Images
How to Make a Wood Bullnose Edge for a Step
On stairs, the overhanging edge at the front of each tread is called a nose, or nosing. When the nose edge has...
How to Cut Bullnose Trim for Stairs
The stairs inside your house have rounded front trim called bullnose trim. This trim protects your toes from getting cracked on the...
How to Convert Carpeted Stairs to Hardwood
While a carpeted stairway adds a warm and cozy touch to the indoor space, removing old, stained, worn out or torn carpeting...
How Do I Get a Bullnose Edge Finish on Concrete Stairways?
A bullnose edge finish puts a rounded edge to your concrete projects. Besides looking good, the bullnose edge helps prevent the edge...
How to Install Hardwood Flooring With a Bullnose Edge
Installing a hardwood floor is a popular homeowner project that can instantly add value of a home. While installing a hardwood floor...
How do I Cap Stairs With Hardwood?
Stair caps, known as treads, are the part of the step that rests atop the stair riser. It is the most visible...
How to Tile Stair Treads
Tiling your staircase treads adds a striking look to your house, while allowing you to avoid the scuffs that come with wooden...
How to Install Wood Bullnose Trim
Many people want to improve the value of their homes by installing hardwood floors. The warm beauty and ease of care make...
How to Install a Bullnose Stair
Bullnose stair treads have a rounded-over edge that protrudes from the staircase. This allows a carpet installer to wrap the carpet over...