Setting the points on the older type distributors was critical to their performance. The points charge the coil between firing of the individual cylinders. Setting the points amounts to adjusting the amount of time the points are open. The larger the gap, the shorter the time the coil is charged and conversely, the closer the gap the longer it is charged. The time the points are closed is referred to as dwell. A dwell meter is needed to fine-tune the dwell because setting the points by hand only is usually not very accurate. Too much dwell and the points will burn. To little dwell will not allow a good coil charge and result in a weak spark.
Things You'll Need
- Common screwdriver
- Phillips screwdriver
- Set of Allen wrenches
- Dwell meter
- Set of feeler gauges
- Remote starter switch
Pull the coil wire out of the coil secondary tower. Remove the distributor cap using a screwdriver. Install the remote starter switch by connecting one of the two leads to the small S terminal on the starter solenoid and the other on the positive terminal on the battery.
Place the transmission in neutral if the vehicle has a manual transmission. Set the initial point gap. Watch the point-rubbing block where the points ride on the distributor cam. Bump the engine over with the remote starter in short bumps until the rubbing block is dead on top of a cam lobe.
Measure the gap between the two sets of points using an 0.018-inch feeler gauge. The feeler gauge should slide between the points with a small amount of friction. If the feeler gauge does not fit between the points or is too sloppy the points must be set. There are two types of points differing only in the way they are adjusted. One type has an obvious screw with a hole in its head made for an Allen wrench and the other has no such screw. This type needs to be adjusted using a screwdriver to loosen a screw in its base enough to spread or close the points followed by tightening the screw. This type has a slot in the base that allows it to be adjusted.
Insert the Allen wrench in the first type of points and turn the wrench clockwise to close the points and counterclockwise to open. Do this while inserting the feeler gauge until you feel a slight drag.
Connect the dwell meter by connecting the black wire lead to the negative terminal on the coil and the red lead to the positive terminal on the battery. Watch the dwell meter scale for your engine: four-, six- or eight-cylinder. If the engine is a four-cylinder the dwell should be 40-45 degrees. A six-cylinder should be 30-35-degrees, and a V-8 should be 23-28 degrees. Crank the engine over with the remote starter and watch the dwell. Adjust the points as previously described to bring them within limits. To reduce the dwell open the points and close them for more dwell.
Remove the remote starter switch and the dwell meter. Install the distributor cap and tighten with the screwdriver. Plug the coil wire into the coil secondary tower.
How to Replace a Ford Point & Condenser Ignition System
Whereas modern Fords feature an electronic ignition system, older Fords relied on a mechanical breaker points and condenser ignition system. While an...
How to Replace Points With Electronic Ignition
Most vehicles built since the 1970s have an electronic ignition system, which replaced the old breaker point ignition system. This change-over made...
How to Set Points on a Small Block Chevy
The older ignition point distributors for Chevy have survived until today. Many of the old classic and muscle cars used the mechanical...
How to Set Points on a Tecumseh Small Engine
Tecumseh manufactures a variety of small engines for use in lawn and garden implements such as lawn mowers, snow blowers and log...
How to Set the Dwell Angle in the Ignition of a 302 Ford
Early 302 engines use a distributor with a point and condenser setup. In this type of distributor the coil is triggered by...
How to Set the Points in a Ford 8N
Setting the points of an 8N tractor is the process of adjusting the gap between two parts in the distributor. Understanding the...
How to Set the Points on a Ford 390
From its inception in 1961, Ford's 390 cubic-inch, big-block engine had one set of ignition points underneath the distributor cap. As the...
How do I Adjust Points on a Willys Jeep?
All Willys' Jeeps were offered with inline four or six cylinder engines and use a contact points ignition, which requires adjustment as...
How to Adjust Points on a Ford F-100 Truck
Ford 6-cylinder and 8-cylinder engines in F-100 pickup trucks have mechanical breaker points mounted on the distributor plate. Lobes on the distributor...
How to Set Points on Ferguson TE20 Tractors
The electrical points inside the distributor cap turn the ignition coil on and off. The ignition coil is the component that increases...