How to Repair Soapstone

Save

Soapstone has become a popular choice for countertops and sinks because of its ease of care and the naturally warm patina it develops over time. Primarily composed of magnesite and talc, soapstone has a high resistance to heat and staining. In the arena of maintenance and repair, one of soapstone's drawbacks doubles as an asset: its softness relative to other stone materials. This means that even though the softness of soapstone makes it prone to small cosmetic problems, softness also makes it easy to repair. Follow a few simple procedures to get your soapstone looking as good as new.

Things You'll Need

  • Mineral oil
  • Cotton hand towel
  • Sandpaper
  • Clear two-part epoxy
  • Light Scratches

    Soapstone's relative softness means that it will inevitably become scratched with normal use. When the surface accumulates light scratches, simply buff the surface with mineral oil and a hand towel. Once rubbed in, the mineral oil will darken the surface, add to its natural patina and hide any light blemishes. For convenience, keep the hand towel for reuse.

  • Deep Scratches or Stains

    Sand deeper scratches or nicks will need to be sanded with medium-grit sandpaper. Due to the stone's softness, the scratch will disappear into the surrounding area with little effort. Once you've sanded away the scratch, move to progressively finer sandpapers until the repaired area matches the rest of the surface. Clean the area of dust with a dry towel or vacuum, and apply a light coat of mineral oil until you've made the area indistinguishable from the rest of the counter. The same procedure applies to stains; lightly sand the stained area, clean and rub down with mineral oil.

  • Chips

    Soapstone may chip if struck hard enough, creating a small area that you must replace. For this repair, you will need a small piece of similar soapstone and a clear, two-part epoxy available at any full-service hardware store or home center. Break the loose piece of soapstone into fine chips and mix with the epoxy. Fill the gap in the soapstone with the mixture and allow to dry as per the manufacturer's instructions. (If the chip appears on the corner or edge of the soapstone, use masking tape to create a mold to hold the epoxy mixture in place.) Once the epoxy dries, sand, finish and oil the affected area as detailed above.

References

Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Fix Chipped Nail Polish

    If your manicure is more than a week old when it chips, it's probably time for a new one. Otherwise you can...

  • How to Care for Soapstone Countertops

    Soapstone is a beautiful and highly resilient material often used throughout the home for decorating in both new home construction and countertop...

  • How to Clean Soapstone Sinks

    Soapstone sinks are a curious mix of impermeability--they're almost impossible to stain--and vulnerability. Although you can set a hot pot on a...

  • How to Sell Inuit Soapstone Carvings

    Inuit soapstone carvings are created by Alaskan and Canadian Native American artists. Carvings typically depict animals or Inuit deities. Old Inuit pieces...

  • How to Repair a Stone Sink

    Nothing exemplifies the incorporation of ancient materials into modern design like a stone sink. Stone sinks, carved from a solid pieces of...

  • How to Repair Cracked Soapstone

    Soapstone gets its name from its greasy, soapy feel. As a talc-schist metamorphic rock, soapstone also goes by the names steatite or...

  • How to Repair Stone Steps With Epoxy

    Epoxy is a type of seal that creates a tough bond between many different materials. Epoxy can also be used to fix...

  • How to Restore a Soapstone Sink

    Soapstone is a natural quarried rock that has a smooth feel almost like running your hand across a bar of soap, which...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!