How to Tile a Bathroom Wall

Save

Tiling your bathroom can add a clean, professional look that your family and guests can enjoy. Wall tile is also an extremely durable material for walls, allowing your work to last years after you finish your project. Tiling your bathroom walls requires extensive preparation, however, to make your project go smoothly. Without the proper steps, you may find your bathroom looking uneven. Lack of planning and incorrect handling of the tiles may even lead to a few of them falling off the wall and breaking.

Things You'll Need

  • Tile adhesive
  • Level
  • Tape measure
  • Gloves
  • Paintbrush
  • Towel
  • Carpenter's pencil
  • Galvanized screws
  • Power drill
  • Tile cutter
  • Tile
  • Grout
  • Grout sealer
  • Backerboard
  • Prepare your surface. Make sure all holes and imperfections get patched. Locate all the studs in the wall while cleaning and repairing the surface as well.

  • Measure the area where you will place the tiles. Use those measurements when cutting your backerboard (backerboard is a rigid board used beneath tile). Drill small holes into the backerboard to help mark where your studs are.

  • Apply adhesive to the wall you will be tiling. Add adhesive with a trowel or a brush. Press the backerboard to the wall and secure it to the wall studs using galvanized screws. Let the adhesive dry thoroughly before attempting any more steps.

  • Create a layout tool by taking a thin piece of unmarked wood or stiff cardboard and laying it next to some tiles you will use. Separate the tiles slightly as if there were already grout between them, and mark your wood or cardboard with their locations. Say you have three tiles laid next to your piece of wood; create a mark for the top and bottom of each tile on the wood (your piece of wood will come out looking like an incomplete ruler). This gives you an idea of how much room your tiles will take and works as a custom ruler for this particular project.

  • Find the center of your backerboard. From this point, take your homemade layout tool and lightly trace mock tiles onto the backerboard. By the time you are finished, you should have a checkerboard design across your backerboard that accurately represents the size and necessary placement of tiles.

  • Spread adhesive across your backerboard with a brush or towel. Work your adhesive in an upward motion. Press the tiles to the adhesive with a twisting motion. Follow the checkerboard lines you created earlier on the backerboard. Tap the tiles lightly with a small block of wood covered in a towel to make sure tiles are secure on the backerboard. Use a tile cutter if necessary to cut tiles to fit at the ends of rows. Allow adhesive to set.

  • Prepare the grout according to the manufacturer's instructions, and smooth it across the tiles. Some grout may get on the tile faces, but ignore that for the time being. After about five minutes, take a wet cloth and gently wipe away the grout on the faces of the tiles. You do not want to accidentally remove grout from between the tiles, so make sure to wipe gently and avoid scrubbing. Allow the grout to dry thoroughly, and apply a grout sealer.

References

Promoted By Zergnet

Comments

You May Also Like

  • How to Tile a Bathroom

    Tile is a popular floor and wall covering in bathrooms where surfaces need to resist water and moisture. A little more expensive...

  • How to Tile Shower Walls

    Shower walls have to be covered in material that is completely waterproof and preferably in something that’s easy to clean. Glazed tiles...

  • How to Prepare Shower Walls for Tiling

    Tiling a shower wall starts with what's behind the tiles. While on any other wall, you can tile directly over the drywall...

  • How to Prepare Bathroom Walls for Tile

    Before you can install tile on your bathroom walls the walls themselves must be prepared properly. Find out how to prepare bathroom...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!