General Motor's 350 engine uses eight intake valves and eight exhaust valves. All sixteen valves open and close at specific intervals. If the valves are not adjusted properly the engine can idle poorly, backfire, and power and fuel efficiency can be substantially reduced. Thankfully, properly adjusting the valves on the 350 is relatively easy, although the valve covers do have to first be removed.
Things You'll Need
- Valve cover gaskets
- Gasket sealer
Start the engine and allow it to reach normal operating temperature.
Remove both of the valve covers. A single valve cover is located on either side of the intake manifold. Each valve cover is attached to its cylinder head with a total of four bolts. Two of the bolts are located on the top of the cover, while the remaining two are on the bottom. Remove the four bolts with a wrench, then lift the valve cover off the cylinder head.
Identify each rocker arm's adjusting nut. The 350 engine uses a total of 16 rocker arms. In the center of each rocker arm is a single nut. It is this nut that is either tightened or loosened to adjust its corresponding valve. Also note that the tip of each rocker arm rests on top of a metal rod, called a pushrod.
Start the engine and allow it to idle. Loosen the single nut in the center of one rocker arm with a wrench until a clattering sound is heard, then tighten the nut just until the clattering stops. Turn the adjustment nut in a clockwise direction one full turn with the wrench to complete the adjustment for that valve. Repeat the processes for the remaining 15 valves, then turn the engine off.
Install the valve covers. Each of the two valve covers use a single gasket to prevent oil from leaking onto the engine. These gaskets are not reusable, and must therefore be replaced. Peel the old gasket off of the valve cover, then apply a single bead of gasket sealer onto one side of a replacement gasket. Place the coated side against the inner lip of the valve cover, then apply a single bead of gasket sealer onto the opposite side of the gasket. Place the valve cover onto the cylinder head, then install and tighten each of the cover's four retaining bolts. Repeat the process for the remaining valve cover.
- Motor's Auto Repair Manual; Ralph Ritchen; 1968
- How to Rebuild Your Small-Block Chevy; David Vizard; 1991
How to Adjust Valves
Drag racers who compete in sanctioned events around the country must be able to produce a vehicle that has reliable performance in...
How to Adjust Engine Valves
If your engine has started to become excessively noisy, you may need to adjust your valves. Over time, valves wear and lose...
How to Adjust Big Block Chevy Valves
Improperly adjusted valves are one of the most commonly overlooked causes of many engine problems, including misfires, a lack of power or...
How to Adjust the Solid Lifters in a Chevy 350
Chevrolet's small-block 350 engine was first used in 1968, and immediately became its most popular small-block. The majority of 350 engines were...
How to Adjust a Valve Lash on a Chevy 350 CID Engine
Most production Chevrolet 350ci engines are equipped with hydraulic tappet (lifter) camshafts that do not need adjustment except in the case of...
How to Adjust the Lash on a Chevy 350 V8
The 350-cubic inch Chevy engine first appeared in 1967 in the Chevrolet Camaro. It was made available in other cars and trucks...
How to Adjust the Valves on a Chevy 350
While it is fairly uncommon to need to adjust valve lash on production Chevy 350 CID small block engines, there are times...
How to Set Valves on a 305 Chevy Engine
The Chevrolet 305-cubic inch, small block, V-8 engine was released in 1976 as a result of Chevrolet's search for better fuel economy....
How to Adjust the Valves on a 383 Stroker
Valve lash is the amount of clearance between the valve-train (rocker arm) and the tip of the valve. Lifters come in two...
How to Adjust a Chevrolet 5.7 Valve
The Chevrolet 5.7-liter (350-cubic-inch) engine employs an overhead valve design that requires occasional maintenance. Adjusting the clearance between the valve stem and...