How to Cane a Chair for Beginners

Save

Add an old-fashioned elegance to your home or patio with chairs made from bamboo or sugar cane. Caned in an open weave, they provide a springy, air-cooled seat and/or back. Wood frames for the cane sections have holes on the rails (sides), which caners use to weave the cane strips into intricate patterns. With use and age, caned chairs dry out and canes break, so re-caning is necessary. Even beginners can accomplish this task by following a few basic steps.

Things You'll Need

  • Wooden chair frame with holes
  • Cane (500-foot half-hank for an 80-hole seat)
  • Border cane
  • Side cutters
  • Dowels or golf tees
  • Wood glue

Vertical, Horizontal and Diagonal Rows

  • Feed cane from bottom up through the back middle hole of a chair seat. Leave a tail several inches long and peg it in place with a golf tee. Feed the cane down through the front center hole on the chair seat, keeping the cane loose. Pull cane up through the next hole to the right in front and down through the opposite back hole. Continue threading the cane through holes toward the right, to the last rail holes. Work with a loose cane, but snug it tight every 4 to 6 holes. Use a second cane to weave vertical strips through holes to the left of the center hole to complete the seat. Use new canes as necessary and peg loose ends with a golf tee.

  • Run a cane horizontally up through the upper right hole and down through the upper left hole, running it over the vertical canes. Keep threading toward the front holes. Straighten canes with golf tees. Tie off all the loose ends from the bottom. Pull the cane tight, then circle the loose end under a nearby cane loop. Do this twice, threading the second loop under the first, and pull them tight. Trim any excess cane ends to 1/4 inch. If there are two ends in one hole, tie them off together.

  • Start a second vertical row in the upper left corner. Loop the second vertical cane through the same holes as the first layer.

    Weave the cane over and under the horizontal layers, keeping it to the right of the first vertical cane strips. Keep the cane very loose for 4 to 6 loops before pulling tight.

  • Weave a diagonal cane up through the upper right corner hole and down through the lower left front hole. Loop the first diagonal cane through holes toward the back left, weaving over vertical canes and under horizontal ones. Weave a second cane toward the right front to complete the first diagonal layer. Start a second diagonal layer at the upper left corner hole and run it down through the lower right corner hole. Weave the cane diagonally under the vertical canes and over the horizontal ones. Start with the rear right half, then the front half. Keep canes straight with golf tees.

  • Finish the weave by looping a round cane around the border. Start at the back rail and insert each end of the border cane into a corner hole. Lay it flat along the line of holes. Run a regular cane up a back hole. Loop it over the border cane, then back down the same hole to hold it in place. Repeat at each hole. Snug the regular cane tight after 4 to 6 holes. Feed border cane ends down each corner hole and hold in place with a golf tee. Skip the corner holes with the regular cane. Peg the canes in the corner holes with a wooden peg that fits snugly into the hole. Apply glue first to make a tight seal to finish the weave.

Tips & Warnings

  • Moisten canes with a sponge dipped in glycerine and warm water for a few minutes to keep them supple.

References

  • Photo Credit Hemera Technologies/PhotoObjects.net/Getty Images
Promoted By Zergnet

Comments

You May Also Like

  • How to Weave a Chair Seat

    How to Weave a Chair. Spruce up an old chair with a cotton, ... Antique rush-seat chairs add old-fashioned flair to a...

  • How to Recane a Chair

    How to Recane a Canoe Seat. As all canoeists who paddle a canoe with cane seats know, ... How to Repair Cane...

  • How to Cane a Round Chair

    Add an old-fashioned elegance to your home or patio with chairs made from bamboo or sugar cane. ... Chair caning is a...

  • How to Refinish a Chair Seat With Rush Weaving

    How to Refinish a Chair Seat With Rush Weaving. ... You cannot strip the old shellac from the rush weaving without damaging...

Related Searches

Read Article

19 Home Decor DIYs That Only Look Expensive

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!