Filling plumbing pipes with pressurized air is a quick and effective way to inspect for leaks in new installation of water pipes and drain/waste/vent systems. You can also air-pressure-test existing pipes, but pumping the drain/waste/vent system full of pressurized air becomes impractical after installation of the plumbing fixtures and connection to the sewer. It's easier and often just as effective to do a water-pressure test instead.
Things You'll Need
- Glue or solder
- Tees and adapters
- Pressure gauge
- Air compressor
Testing New Plumbing
Cap all the stub-outs connected to the system you're testing. For a DWV system, this usually means gluing a cap to each stub-out with plastic pipe cement. If you're testing a water system, you may have to glue or solder the caps, depending on the type of pipes in your system. You'll cut off the caps when the test is complete.
Install or find a fitting that allows you to connect an air compressor hose and pressure gauge to the system. In waste systems, you usually do this by screwing an adapter to a clean-out fitting and installing a tee. For water systems, it usually works to leave one stub-out uncapped and install a tee and adapter for the hose and gauge on that stub-out.
Turn on the compressor and fill the pipes with air until the gauge reaches the test pressure reading. For water systems, this reading is usually around 80 psi. For drain systems, it's much lower -- about 5 psi.
Turn off the compressor and leave the system pressurized for 15 minutes. Any reduction in pressure during that time signifies the presence of a leak.
Air-Testing Existing Plumbing
Air-test a system of water pipes by turning off the main shutoff valve and draining the water from the system. After all the water has drained, turn off all the faucets.
Screw a pressure gauge to one of the faucets -- usually a laundry-room faucet or outdoor faucet with a threaded spout. Screw an adapter to another faucet that allows you to connect a compressor hose.
Charge the system to about 60 psi and leave it charged for 15 minutes. The system has no leaks if the pressure gauge remains stationary.
Water-Testing Existing Plumbing
Test a water system without draining it by locating an outdoor or laundry faucet to which you can attach a pressure gauge.
Screw the gauge to the faucet spout, open the faucet all the way and turn off the main shutoff valve for the house.
Watch the gauge for 15 minutes. If it moves, there's a leak in a pipe or in a faucet. Check the faucets, and if none of them are dripping, the leak is in a pipe.
Tips & Warnings
- If you don't want the pressure-test to include the faucets or toilet fill valves, turn off the shutoff valves for these fixtures.
- Plumbers often use smoke to test existing drain/waste/vent systems. They block the drains and the path to the sewer with a balloon, fill the system through the roof vent to a pressure of 5 psi, then block the roof vent. Any leaks in the system are easy to detect, because smoke pours out of them.
- Photo Credit nattrass/iStock/Getty Images
How to Test New Plumbing Lines
After installing new plumbing, test the lines for leaks with air pressure or water.
How to Pressure Test Air and Water Lines
Pressure testing water lines and air lines is the most secure way of knowing whether a leak is present. Many times relying...
Testing Plumbing for Leaks Using Air vs. Water
Testing for Plumbing Leaks; How to Pressure Test Plumbing; How to Test Household Water Pressure; Will a Leak in My Plumbing System...
Master Plumber Exam Example Questions
The master plumber examination is a group of exams that test a plumber's knowledge of state and federal plumbing regulations and codes....
How to Test Drain Pipes
If a pipe passes the air test, it will be watertight as well as airtight. Water, being a larger molecule, ... How...
How to Test Household Water Pressure
The process of testing a home's water pressure is not expensive or difficult ... How to Pressure Test Air and Water Lines;...
What Is the Mill Pressure Test for Pipe?
The mill pressure test, or hydrostatic test, samples pipe quality. Pipe integrity is tested by sealing a segment of pipe, filling it...
How to Pass the Journeyman Plumber Exam
In some states, plumbing-exam programs are run entirely out of this office. In other states, ... If you are just beginning the...