How to Make Stair Treads & Trim

Save

A staircase consists of three main components: stringers, which are the angled supports on the sides of the staircase that hold everything up; risers, which are the vertical front boards between the steps; and treads, which are the horizontal surfaces of the steps. The treads are the most visible part of the finished product, so its important to choose high-quality boards.

Things You'll Need

  • Enough 2-by-10 pine or oak board board to provide all the treads you'll need. (Determine the necessary footage by multiplying the width of the staircase by the number of steps.)
  • The same footage of 1- or 2-inch wide wood trim designed to cover inside corners.
  • Tape measure
  • Tri-square
  • Pencil
  • Circular saw
  • Power drill with screwdriver bit
  • Belt sander with medium-grit sandpaper
  • Box of long wood screws
  • Box of trim nails
  • Hammer
  • Nailset
  • Measure the width of the stairway at the tops of the stringers. If the stairway has a wall along either or both sides, measure to the wall. Otherwise, measure to one inch beyond the stringers.

  • With your pencil, mark the 2-by-10 board at the measurement you took. Use the tri-square to make a straight line across the board at the mark. With your circular saw, cut the board at the line.

  • Take your newly cut tread and lay it lengthwise on top of the remaining portion of the board, with the ends flush to each other. With your pencil, trace a line along the other end of the tread, onto the surface of the remaining board, to duplicate the length of the tread. Remove the tread and cut the board at the line. Repeat until you have as many treads as you need.

  • Set the boards in place on top of the stringers, and secure them using the drill and wood screws, drilling straight downward on the face of the tread into the top edges of the stringers. Use three screws on each end of each tread, arranged in a straight line. Sink each screw just below the surface of the wood. If there is a center stringer, screw the tread into that as well.

  • Run the belt sander along the front face and upper edge of each tread, to smooth the front and remove the sharp corners. If the sides of the treads will be visible, sand the sides as well.

  • Measure for placement of the trim, which will tuck into the rear inner angle of each step, where the risers and treads meet. Cut the trim pieces to size and nail them to the stairs with trim nails. Sink the nails to just below the surface of the wood with the nailset.

Tips & Warnings

  • Always wear eye protection when using a circular saw.

Related Searches

  • Photo Credit http://wilsonremodeling.net/Pictures/Oak_Stair_Treads.htm
Promoted By Zergnet

Comments

You May Also Like

  • How to Make a Stair Tread Gauge

    When stair treads sandwich between vertical surfaces such as walls, stringers or skirting, the dimensions and angles depend on the squareness and...

  • How to Trim Out Stairs

    Trim is an important detail that gives your staircase an attractive, finished look. With the high cost of solid wood trim, you...

  • How to Make Stair Treads From Hardwood Flooring

    When you build a staircase, you must makes stair treads, which provide the stairs' walking surface. Generally, stair treads are built from...

  • How to Make a Stair Tread Jig

    You can spend $90 and up on a commercial stair tread jig or make your own out of scrap plywood. Some woodworkers...

  • How to Cut Stair Treads

    Whether you're building a new set of stairs or just replacing an old stair tread, cutting the stair tread correctly the first...

  • How to Do Stair Trim Molding

    Floor moulding and trim flows from ground floor to upper floor by following the contours of the stairs. Moulding along stairs follows...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!