How to Build Lattice Privacy Screens

Save

If you have a swimming pool, hot tub or a special spot for tanning or you just want a little privacy, a lattice privacy screen is easy to construct, looks nice and can be completed at a very reasonable cost. With the design below you can build a single section or add additional screen sections for more privacy.

Things You'll Need

  • Four 2-by-2-by-8s
  • Tape measure
  • Saw
  • Six 3-inch wood screws
  • Screwdriver
  • One 2-by-2-by-10
  • One 4-by-8 sheet of lattice
  • 50 1-inch wood screws
  • Four 1-by-4-by-8s
  • Post hole digger
  • Level

How to Build Lattice Privacy Screens

  • Assemble the frame. Lay out the four 2-by-2-by-8s. You will cut two of these to a length of 7 feet and 8 1/2 inches. Put the two cut pieces inside the two full length pieces, one at the top and one 4 feet down. Secure these in place using the 3-inch wood screws. Now lay the 2-by-2-by-10 board diagonally across the rectangle you have just built. Make certain the frame is square, and then mark the board so it will fit tightly into the opening. Cut the board, and secure it in place with 3-inch wood screws.

  • Attach the lattice. The frame is now ready for the lattice. Double check to make certain the frame is square. Measure across the frame diagonally and record the measurement. (Measure from the other two corners and make certain the measurement is the same. If not, adjust the frame until these two measurements match.) Lay the lattice on the frame and secure it down one side with the 1-inch wood screws. The lattice will have some play to it, so keep your frame square and arrange the lattice to fit the frame. Once they are in alignment, secure the other three sides of the lattice with more 1-inch screws.

  • Install the facing. Cut 45-degree angles on the ends of two of the 1-by-4s. Install these boards on each side of the frame with the angle cut at the top. On a third 1-by-4, cut 45-degree angles on both ends. Install this along the top so the angles match up with those on the two side boards. Measure the distance between the two side boards, and cut the last 1-by-4 to this length. Install the last 1-by-4 with its base flush along the bottom of the lower 2-by-2. This will form a frame/facing around the lattice.

  • If you intend to paint the screen, the easiest method will be to use a spray painter to get good coverage on the lattice and to save time. You can also purchase the pre-painted lattice and need to paint only the facing and framework. Paint the entire frame and facing, even the portions that will be buried. This will provide additional protection from rotting. You may want to consider painting the lattice one color, such as white, and the facing a second color such as brown or earth-tone.

  • Erect the screen. Determine the location for the screen, and mark the location for the base of the screen. Use a post hole digger to dig two holes 24 inches deep. Place the legs of the screen into the holes. Make certain the screen is level, and then begin backfilling the holes with dirt. If you want a more permanent setting, fill the holes with cement. You may need to install temporary braces to support the screen until the concrete sets.

Tips & Warnings

  • Use pressure-treated wood to maximize the lifespan of your screen.
  • Be certain to double-check and triple-check that the screen is square at each stage of assembly.

Related Searches

Promoted By Zergnet

Comments

You May Also Like

  • How to Make a Frame for Lattice

    Create a frame for your lattice work to enhance an outdoor area and give your landscaping a new look in just a...

  • How to Attach Patio Screen Lattice Panels

    Attaching lattice panels to your patio can make for a nice screen against the elements, bugs, and other people. You can attach...

  • How to Build an Outdoor Privacy Screen

    This cedar wood screen adds loads of character to a back yard, is budget friendly, and gives an outdoor patio space extra...

  • How to Build a Deck Privacy Screen

    An outdoor deck with a railing that's only waist high may suffer from privacy issues. If you don't want neighbors and passers-by...

  • How to Build a Lattice Privacy Wall

    If you're trying to add a little privacy around your pool or backyard, you can build a lattice privacy wall to keep...

  • How to Build an Outdoor Privacy Panel

    Perhaps you enjoy relaxing on your patio or terrace but are not so fond of the neighbors watching your every move. Urban...

  • How to Build Vinyl Lattice Screens

    Vinyl lattice screens are an ideal way to camouflage unsightly areas, provide privacy or add interest to a garden. They are also...

  • How to Build a Lattice Panel

    Lattice panels are a versatile building material. You can use a basic lattice panel for fencing, privacy screens, trellises and to screen...

  • Lattice Privacy Fence Ideas

    Lattice is a material commonly used in gardens, consisting of criss-crossed strips of wood, vinyl or metal that form diamond or squares...

  • Privacy Screen Ideas

    You can find examples of outdoor and indoor privacy screens in different cultures all over the world, from the paper room dividers...

  • Privacy Lattice Panel Ideas

    If you wish there were more privacy in your front or backyard, a lattice panel fence may be the solution. A lattice...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!