How to Frame a New Interior Wall & Door Frame

A homeowner who feels confident in proceeding with basic carpentry jobs may hesitate when confronted with building a wall that will have a door. Framing a door opening is not difficult, however, and anyone who can frame a basic wall can do it by following these steps.

Things You'll Need

  • 2x4 lumber
  • Tape measure
  • Circular saw
  • Hammer
  • Galvanized nails
  • Electric drill
  • Wood or masonry screws

Instructions

    • 1

      Measure and cut two pieces of 2x4 lumber to the same length as the wall section you are building. These will serve as the top and bottom plates for your wall.

    • 2

      Get the rough opening dimensions for the door you purchased; it should be noted in the material that came from the manufacturer. Mark the door's rough opening width on both the top and bottom plates. Place additional marks on both plates, 1 1/2 inches and 3 inches on either side of the rough opening. The outside marks at 3 inches will be the location for the king studs, and the inner 1 1/2 inch marks will be the location for the jack studs that will frame the door.

    • 3

      Use 2x4 lumber and measure and cut the wall studs to the same length as your wall height, minus 3 inches. Nail the wall studs every 16 inches on center between the top and bottom plates as shown in the diagram, except for the area you marked for the rough opening, king, and jack studs.

    • 4

      Measure and cut two additional studs to the same size as the previous wall studs. These will be the king studs. Nail them into place on the marks you made for them.

    • 5

      Measure and cut the two jack studs to a length of the height of your rough door opening, minus 1 1/2 inches. Nail the jack studs into place, inside the king studs and on the marks you made for them.

    • 6

      Measure and cut a 2x4 to the length that equals the distance between the king studs. Place it flat on top of the two jack studs and nail into place. This will serve as the header for the door.

    • 7

      Measure the distance from the top of the header to the bottom of the top plate. Cut a 2x4 to this length and place it as a cripple stud between the center of the header and the top plate. Nail it into place.

    • 8

      Raise the wall into place and check that it is plumb. Screw the bottom plate securely to the floor and nail or screw the top plate to the structure above it. Your framed wall and door opening are complete.

Tips & Warnings

  • Be sure there are no electrical wires or plumbing in the area before you nail the top plate into place.
Related Searches

Resources

  • Photo Credit http://www.kookerkids.com

You May Also Like

  • How to Frame a Wall With a Door

    Whether you're building a home, finishing a basement, or just changing an existing floor plan, knowing how to frame a wall with...

  • How to Frame a Wall for a Pocket Door

    Pocket doors are a practical solution to the need for a door in smaller spaces, such as closets or bathrooms, where a...

  • How to Build an Interior Door Frame

    Building a interior door frame can be a simple job if you set yourself up right. ... How to Frame a New...

  • How to Build a New Interior Wall

    How to Build a New Interior Wall. When doing home improvement projects, sometimes it is necessary to build an interior wall. ......

  • Doors That Slide Into the Wall

    Doors That Slide Into the Wall. Doors provide an important functional purpose in your home, ... How to Remove an Interior Sliding...

  • How to Build an Interior Wall

    How to Build an Interior Wall. An interior wall can be built with some time, ... Building a interior door frame can...

  • How to Frame a Door Opening

    How to Frame a Door Opening. ... How to Frame a Wall With a Door. Whether you're building a home, finishing a...

  • How to Frame Interior Door Headers

    Interior doors are framed very similar to exterior doors. The only real difference is that most interior walls are built out of...

  • How to Build a Pocket Door

    Pocket doors are sliding doors that run on a track built into the wall. Rather than swinging open on hinges like most...

  • How to Seal Your Garage Door & Build a Wall

    Check the interior and exterior of the door opening for gaps that may allow air transfer. ... How to Build a False...

  • How to Install a Doggy Door

    Interior Design. Home Design; Home Décor; Furniture; Housekeeping. Cleaning; Organizing; Laundry; ... How to Frame a Doggie Door for a Wall. How...

  • How to Frame a Wall

    Building repairs or remodeling can be major projects. Often a new wall has to be built in order to expand a room...

  • How to Use a Pressure Washer

    We'll need to wait for our pressure to build up. As you can see, once it builds up, ... How to Troubleshoot...

Related Ads

View Blog Post

DIY Himmeli-Style Christmas Star Tree Topper