# How to Build Wooden Steps for Mobile Homes

Save

You can learn to build stairs for a mobile home or trailer in few steps. Why hire an expensive handyman or professional carpenter when you can tackle the project yourself? Most trailers and mobile homes are sitting on a concrete base on the ground, with a slab for the stairs already in place. If there is no slab present, you can easily construct one to accommodate a set of stairs.

### Things You'll Need

• Circular saw
• Hammer
• Tape measure
• Framing or carpenter's square
• Pencil
• Lumber
• Nails
• Concrete screws or powder actuated gun
• Stringers
• Square gauges
• Wood screws
• Take measurements for the stairs:
First, measure the height of the stairs; you will want to keep them a couple of inches below the door opening: this measurement will be the total rise.
Next, measure the length of the stairs; most stairs are built with a 30 to 35 degree angle slope. The length is otherwise knows as the total run of the stairs.

• Measure the riser height:
First, write down the total rise; then convert the total rise to inches. Divide the total rise by 7 (7 is used because this is the recommended height in inches of all stair risers). Take this number and divide it into the total rise. Take the numbers to the right of the decimal and convert these to inches by dividing them by 16. (You use 16ths because that is how many fractions of an inch there are on a tape measure.)

Example of how to get unit rise:

``````              4'6" total rise
4' multiplied by 12"=48"+6"=54" total rise in inches
54" divided by 7"=7.714" So there will be 7 total risers for the stairs
54" divided by 7=7.714; Convert .714 to inches
.714 multiplied by 16=11.424 or 11/16 of an inch.``````

According to these measurements, the unit rise will be 7-11/16 inches and the stair set will contain seven steps.

• Measure the tread width:
Convert the total run to inches by multiplying the feet by 12 and then add any leftover inches. Divide this number by 6. Minus 1 from the total number of steps needed for the stairs; you must do this because the concrete slab is counted as a tread. Convert the decimals into inches, and then multiply the three numbers to the right of the decimal by 16.

Example to get tread width:

``````               5'3" total run
5' multiplied by 12"=60"+3"=63" total run in inches
63" divided 6=10.5
.5 multiplied by 16=8 or 8/16 or &#xBD; inch.
Tread width will be 10&#xBD; inches``````

The tread is 10½ inches and the riser is 7-11/16 inches. According to the measurements, there are seven steps and six treads.

• Lay out and cut the stair stringers:
The stringer will be either 2x10 or 2x12 pieces of lumber. The stairs will need only two stringers, but you can build with more if you prefer. Take the framing square and tighten the square gauges on the outer edge at the unit riser height and tread width. The tread will be on the tongue of the framing square and the tread will be on the blade of the framing square. (The tongue is the shorter end of the framing square while the blade is the longer end.) Place on the stringer and trace out each step, sliding the framing square to the right so that the tread measurement lines up with the last riser line. (Your last tread mark will be part of the landing.)
Reverse the framing square and mark the bottom of the first step. Move the square to the top end of the stringer. Align the tongue with the last riser line and mark the top cut.
Cut the stringers, stopping the saw at the end of each line and using a cut out saw to finish the cut. Cut out a notch at the bottom of the stringers to accommodate the bottom plate that you will attach to the concrete slab in step five.

• Construct the stairs:
Fasten a bottom plate, usually a 2x4, to the concrete slab using a powder actuated nail gun or self tapping concrete screws. This plate will be located where the bottom face of the stairs will be located. There are several ways to attach the stringers to the house; you can nail directly into the joist of the house, nail a ledger plate to the joist to set the stringers on, or use brackets to hold the stringers to attach to the house. Cut the treads out of lumber best suited for outdoor environments. Use split treads, two treads per step, to allow water to drain. Glue with wood glue and screw in place.

## Related Searches

Promoted By Zergnet

## Resources

### You May Also Like

• Where to Find Door Steps For a Mobile Home

Mobile-home stores sell a variety of doorsteps in wood, concrete, fiberglass and steel. Before you buy steps, though, you should check with...

• How to Build Wooden Steps

A stairway is based on the fundamental inclined plane. It is easier to gradually move up a ramp than it is to...

• How to Build Wood Porch Steps

Wooden steps are the finishing touch to any porch or deck, providing not just safe, easy access, but a touch of beauty....

• How to Build Moveable Steps

Movable steps are handy to have around the house to reach items that may be stored in high cabinets or for children...

• Porch Styles for Mobile Homes

Once you move all of your furniture and other items into a mobile home, it might seem a bit cramped. Create a...

## Related Searches

Check It Out

### 22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.