Things You'll Need:
- Electrical tape,Although a bit heavy, only small lengths are required so it doesn't add much weight overall.
- Lightweight, clear sticky tape. Scotch tape, Sello-tape, sticking tape, about the width of your finger.(1/2 inch) in width
- Large, translucent (see-through), colored plastic bags-you must be able to see a black pen lines through the plastic.
- dark garbage bags, for tails.
- BBQ skewers
- (20 pound) or more flying line
- Wood glue
- A ruler
- A black marking pen
- scissors
- calculator
- flat surface to work on
-
Step 1
* cut the point off a skewer, then measure it to establish '1 skewer length' for your kite
* cut the point off another skewer, to exactly the same length as the first one
These will be referred to as the 'spars' from here on. -
Step 2
The template shown represents one side of the kite sail. You will now transfer these measurements to the sail plastic as follows... * firstly, take the large freezer bag that you will be using for the sail, and lay it flat on the table
* measure and mark the half-way point on the horizontal spar then lay the spars down on the plastic to show where the sail corners are
* mark the corners of the template shape with dots,- notice that marks are also made on the side edge of the bag, which is the center-line of the kite sail
* using the marking pen, rule lines between the dots
Getting the spars at 90 degrees to each other by eye will be quite accurate enough, if you are reasonably careful. -
Step 3
* flip the plastic bag over, and trace over all the black lines using your marker pen and ruler
* cut out a rectangular section of the bag containing the kite sail, open it out and lay it flat on the table - you can now see the complete sail outline, as in the photo -
Step 4
* lay clear sticking tape along all the lines with each line showing through the center of the tape - that's 4 pieces of tape in all
* with scissors, cut along the black lines - this will leave some of the sticking tape inside the sail outline
Tip: Try to leave less than half the width of the tape on the inside of the black outline. It's important to save weight on such a small kite. Also, don't worry about overlapping lengths of tape at the corners, it will all look tidier after the cutting is done.
The tape is hard to see, so the red rectangles indicate where the pieces are.
* Place the unmarked bamboo spar on the plastic, in a vertical direction, with the edge tape facing up
* Cap the ends of the spar with tape, as in the photo, by sticking it down over the bamboo and plastic then folding it under the plastic to stick on the other side - a bit tricky, take your time!
* Next, lay down the horizontal spar and cap each end with tape - pull the slack out of the plastic, but don't pull it really tight
* Secure the horizontal spar to the vertical spar with 2 drops of glue, one above and one below where the spars cross, as in the photo
* If you want to, trim the bits of tape that stick out at the top and bottom of the spar, with scissors -
Step 5
* Cut off some flying line to a length of 3 skewers, and tie a very small loop into each end
* Poke 2 holes in the plastic sail at each of the bridle attachment points - one hole on either side of the spar, so 4 holes altogether
* Tie each end of the line to the bamboo, through the holes - use a single half-hitch, and pull tight against the knot of the small loop
Now take a length of flying line about half a skewer long, and tie one end to the bridle line with a Prussik knot. Tie a small simple overhand loop into the other end, just to get a big knot. -
Step 6
* Make up a tail from another freezer bag, making sure it is at least 6 times as long as the diamond kite itself
* Attach the tail by poking one end between the bottom of the vertical spar and the sail plastic
* Pull the rest of the tail through the loop, but don't over-tighten
See the photo, where I have left the tail a bit loose to make it clear. After the photo, I tightened it and pulled it down the spar as far as it would go.
At this point, you've pretty much finished making the 1-skewer diamond! -
Step 7
Finally, make up a flying line and attach it to the bridle with a Lark's Head knot. See the photo above.
As a final check, suspend the kite from the flying line. Shift the Prussik knot along the bridle line until the kite hangs at about a 30 degree angle from the horizontal.
