The oxygen sensor in your car is constantly monitoring oxygen content in exhaust gases from your engine. This helps the vehicle computer adjust for the proper fuel/air mixture, which affects drivability. If you are looking for the cause of an engine-performance problem, a sudden increase in gasoline consumption, or if the car computer code is pointing you toward the oxygen sensor, follow these simple steps to verify the oxygen sensor's proper operation. Even performing these tests as part of a maintenance program will greatly benefit your car engine. So let’s get started.
Things You'll Need
- Oxygen sensor removal socket
- 10-megaohm digital voltmeter
- Notepad and pencil
Locate the oxygen sensor in your vehicle. Follow the exhaust pipe at the exhaust manifold. You should find the sensor threaded into the exhaust pipe ahead of the catalytic converter.
Inspect the oxygen sensor electrical connector for damage. Make sure it is free of dirt and grease. Keep the sensor harness a reasonable distance from the exhaust to avoid damage to the connector and wires.
Idle the engine for about three minutes, then turn off the engine. Remove the oxygen sensor using a ratchet and oxygen sensor removal socket, keeping your hands and arms away from the exhaust pipe to avoid burning yourself. Closely inspect the tip of the sensor and make sure it is not heavily coated with carbon deposits. Thread the sensor back into the exhaust pipe.
Check the voltage signal coming out of the oxygen sensor using a 10-megaohm digital voltmeter. Hook up the voltmeter's red probe to the sensor’s signal wire and the black probe to engine ground.
Start the engine and let it idle for about two minutes while watching the digital reading on the voltmeter. It should be fixed for a short period at around 0.1 or 0.2 volts. After two or three minutes, the voltage reading will begin to fluctuate between 0.1 and 0.9 volts. If the sensor takes four minutes or more to begin fluctuating, replace it.
Jot down in a notepad the lowest and highest voltage reading from the digital multimeter in any one-minute period. The voltage should fluctuate constantly between 0.1 and 0.9 volts. If the voltage goes above this range, remains below 0.5 volts or stays fixed at a particular voltage, replace the oxygen sensor.
Disconnect the PCV valve vacuum line with the engine running. As the engine stumbles, watch the voltmeter reading. It should go down to about 0.2 volts. Reconnect the vacuum line.
Open and close the engine throttle with a quick motion. The sensor’s output voltage should go up and down accordingly.
Block the air intake duct using two or more rags. The sensor’s output voltage should go up to about 0.9 volts. If the sensor response is out of these voltage specifications, replace it.
Tips & Warnings
- Inspect the exhaust manifold and fuel injectors for leaks, as well spark plug condition and other ignition components that may affect oxygen sensor operation before discarding the sensor.
- It is recommended to replace a 1- or 2-wire oxygen sensor every 50,000 or 60,000 miles. 3-wire sensors should be replaced after 100,000 miles of service.
- Consult your vehicle service manual to easily locate, identify wires and components. You can buy a vehicle service manual at most automotive parts stores or check out out one for free at most public libraries.
- Do not attempt to clean an oxygen sensor with solvent or water to avoid irreparable damage.
- Only use a high-impedance or 10-megaohm digital voltmeter for these tests, or you could damage the oxygen sensor’s circuitry.
Knock Sensor Problems
Knock sensors refer to sensors -- typically attached to the engine’s cylinder head or block -- that send signals to the ECU,...
How to Troubleshoot an Upstream Oxygen Sensor
An O2 sensor measures the contents of the exhaust gasses coming out of the engine. These types of sensors are typically plugged...
How to Repair the Oxygen Sensor in a Toyota
The Toyota has oxygen sensors that will need repair work. Deciding which sensor is in need of serious replacement can be more...
How to Repair Oxygen Sensors
Oxygen sensors monitor fuel-to-air ratio being expelled from the engine into the exhaust system. Since 1995, the number of oxygen sensors on...
How to Troubleshoot an O2 Sensor
Computer controlled vehicles use oxygen sensors to allow the computers to tune the engine for the most efficient operation and the lowest...
How to Fix a Focus O2 Sensor Problem
The oxygen (O2) sensor in a vehicle is mounted in the exhaust manifold, and it measures the oxygen content in the exhaust...
Normal Map Sensor Readings
A MAP sensor is a load sensor that communicates to the car's computer system how much air is entering its engine. It...
Troubleshooting Oxygen Sensor Problems
Oxygen sensor problems will cause a vehicle's "check engine" light to come on, and some of the symptoms of oxygen sensor problems...
Problems Caused by O2 Sensor
A car's O2 sensor is a main component in keeping your car in smooth-running order. There are many warning signs that are...