If a wet bar is placed in an area already served by (or having close access to) existing water lines (including the main water line as well as hot and cold water lines), installing the plumbing for a wet bar is much easier. For the purpose of this article, we will assume that this is the case.
Things You'll Need
- Tape measure
- Pipe cutter, hacksaw or similar pipe-cutting tool
- Plastic pipe suitable for plumbing use
- Pipe fittings (straight and curved)
- Solvent cement
- Face mask
Shut off the water supply. (It is probably best to do this to the whole house while completing this project.) Open all faucets and allow the pipes to drain as much excess water as possible.
Cut into the hot and cold water lines, using your pipe-cutting tool.
Use the “T” fitting as a placement tool to mark where the water line will need to be taken out to accommodate new piping, and cut the section(s) out.
Clean and smooth the cut ends of the pipes thoroughly.
Measure the amount of plastic pipe you will need to run water lines from where you tapped into the water source to your wet bar area. CAREFULLY cut the plastic pipe, using a fine-toothed saw or hacksaw, to the desired lengths.
Repeat Step 4 for the plastic pipe that has been cut, as well as for any fittings you will be using to join the pipe.
Brush the solvent cement onto the pipe end(s) and fitting(s). Use a LOT of solvent cement on the pipe end(s); use a little less on the fitting(s). Make sure that all surfaces of the pipe end(s) and fitting(s) are thoroughly covered.
Immediately join the pipe end(s) and fitting(s). When you do, give them a little twist. This will ensure you get a tight fit.
Use pipe fittings that curve at a 90-degree angle to bring the pipe through the wall and out to where it will connect with the wet-bar sink. (It may be necessary to measure and cut additional pipe where it comes out from the wall.)
Install the sink and other appliances according to the manufacturers’ instructions.
Tips & Warnings
- Using plastic plumbing pipe will allow you to join pipe sections and ends using “solvent” welding as opposed to conventional “heat” welding.
- When joining pipe end(s) and fitting(s), you WANT to see solvent cement oozing out of the pipe end(s). In this way, you will know for sure you have used enough solvent cement. You may leave this excess, or you can wipe away some of it, leaving only a thin film.
- Remember that while plastic pipe is easier to work with, it may not support as much water pressure as pipe made of heavier material. You may want to adjust your water pressure accordingly.
- Don't rush. Be careful when joining the pipe end(s) and fitting(s). You can’t “undo” pipes and fittings once the solvent cement has been applied and dries—and it dries quickly!
- Don’t breathe solvent cement fumes for too long, if at all. Wearing a face mask that will filter odors is a very good idea.
- Be careful when using the pipe-cutting tools. Even fine-toothed saws can be sharp and cause severe injury.
How to Install Security Bars On Your Windows
Since they are often out of a neighbor's view or hidden by bushes or shrubs, basement windows make an easy point of...
How to Install Grab Bars in a Bathroom
Slips and falls in the bathroom are a major cause of injuries to people of all ages. Properly mounted grab bars (installed...
How to Build a Wet Bar
Adding a wet bar can be a great weekend project that can add value to your home. Wet bars can help you...
How to Install a Towel Bar in a Bathroom
Install a towel rack on drywall or tile using screw anchors. If installing on drywall, try to locate one end of the...
How to Install a Plumbing Stub Out
Plumbing stub outs are used to extend pipe installed below slabs or inside walls out of the structure and into the room...
How to Design a Wet Bar
A wet bar is a luxury space in the home with many practical purposes. What those seeking to install a wet bar...
Simple Wet Bars to Put in Your Home
If you're serious about entertaining, a wet bar is a useful and stylish addition to your home. Wet bars provide space for...