How to Make an Easter Egg Tree

Save

In a sea of candy-coated and pastel Easter decorations, making a neutral-colored egg topiary is a refreshingly subdued yet festive way to welcome spring. It's a versatile item that would look equally beautiful in a living room, kitchen or entryway. The best part of this project is that it doesn't require much crafting experience or time.

Make a craft-colored egg topiary tree to welcome spring.
(Megan Andersen)
  • 4-by-6-inch terracotta pot, 1
  • Floral foam
  • Serrated kitchen knife
  • Straight stick that measures at least 1/4 inch in diameter and 10 inches in length
  • Scissors
  • 1 package of craft moss
  • Burlap (enough to wrap your pot)
  • Hot glue gun and hot glue sticks
  • Ribbon in any color and width you like (enough to wrap your pot)
  • Jute twine
  • Craft foam in a sphere shape, 4 inches
  • 30 2-inch papier-mache eggs
  • 1 hat pin or glass-head pin

Tip: A willow, bamboo or wooden dowel will work for the stick, and papier-mache eggs are available seasonally at craft stores.

Gather the materials needed to make an egg topiary.
Megan Andersen

Use the serrated kitchen knife to cut your floral foam brick down so that it fits snugly into the base of your pot. Insert your straight stick into the center of the foam.

Use floral foam to secure your stick.
Megan Andersen

Use your scissors to cut a couple pieces of craft moss that are large enough to cover the floral foam base. Overlap one piece of moss over the other for a layered look. Cut a slit in the top piece of moss so it will fit around the stick. To avoid the visible straight seam (as shown), use your scissors to create a jagged, more natural-looking edge.

Cover the foam with craft moss.
Megan Andersen

Cut a length of burlap that is long enough to wrap around your pot with about 1 inch of overlap. The height should be enough that it covers the base of the pot. Secure the burlap in place with hot glue. The glue will seep onto the pot, which will keep it from slipping.

Warning: Always be mindful of your fingertips when using hot glue, especially when it can seep through the fabric.

A ribbon of burlap makes a beautiful, textural sleeve for your pot.
Megan Andersen

Add color by wrapping ribbon around the center of the burlap. Bring the ribbon ends together in the same place where your burlap ends met, and secure it in place with hot glue.

A bead of hot glue secures your decorative ribbon in place.
Megan Andersen

Cut a long length of jute twine from the spool and tightly wrap it around the pot, centered over the colorful ribbon. Secure the jute by tying a decorative bow at the front of the pot. Cut away any excess cord tails. You can secure the bow to the ribbon with a dab of hot glue if you like, but it's not necessary.

Wrap a jute cord around your colorful ribbon, and secure it with a decorative bow.
Megan Andersen

With your base complete, grab the 4-inch foam ball and firmly press it 2 to 3 inches into the stick.

Pierce the foam ball with your stick.
Megan Andersen

Take the foam ball off the stick. Unwrap a sheet of craft moss, and put the foam ball in the center of it. Begin wrapping the moss around the entire sphere. Do not cover the hole in the sphere where you pierced it with the stick. Fold the moss over and around the entire surface, using the tacky side of the craft moss and hot glue to secure the moss in place.

Note: Depending on the brands, some foam may melt a bit when it comes in contact with hot glue. Using a small ball of the same foam as a test is always wise, but using the hot glue gun in zig zag motions while dispersing the glue (rather than one concentrated blob) will lessen any noticeable pits that may occur. The moss is an extremely forgiving surface, so if some depressions form, you may not even notice it.

Moss will peek through any egg gaps.
Megan Andersen

Use your scissors to cut away any lumpy or over-folded areas of moss. The moss will just act as a background, so it doesn't need to be a perfectly even surface. Stick the moss-covered sphere back onto the stick.

Trim away any excess moss with scissors.
Megan Andersen

To wrap some of your papier-mache eggs in jute twine, begin with a squirt of hot glue at the tapered end of one egg. Working with your jute still on the spool, fold a 1/4-inch end of the cord and carefully press it into the glue. You can secure it in place with a hat pin while the glue dries. Then, tightly wrap the jute around half of the egg, occasionally squirting hot glue along one side of the egg, before pressing the cord into it.

Start with a bead of glue and hat pin to hold the jute in place.
Megan Andersen

When the egg is half-wrapped and the hot glue is dry, turn the egg upside down and wrap the second half, squirting hot glue as you go. When the egg is fully wrapped and the glue is dry, cut the jute with your scissors and remove the pin. Your first jute-wrapped egg may take you a few minutes to complete, but the more you make, the quicker you will get.

The jute-wrapped egg
Megan Andersen

Wrap roughly 15 of your 30 eggs in jute. The increased size of the jute eggs will ensure that your sphere surface is completely covered.

Two options for natural-looking eggs
Megan Andersen

Working from the bottom up, begin gluing the eggs (both the jute-wrapped and bare papier-mache) to the craft moss sphere. Turn the eggs in different directions as you glue them down.

Begin from one side of the sphere and work your way around.
Megan Andersen

When you are done, pull off any hot glue strings, and scrape any visible glue off with your fingernail.

Tip: If your glue was particularly messy, use a hair dryer to heat up the excess glue and remove it with your fingers.

Ready for spring!
Megan Andersen
Promoted By Zergnet

Comments

Read Article

How to Make Red Wine Sangria

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!