DIY Wood Pallet Christmas Tree

Save

Decorating for Christmas and saving money doesn't always go hand in hand. This holiday season, skip the expensive store-bought decor and turn an old pallet into a Christmas tree instead. Festive for indoor or outdoor display, this DIY is wallet-friendly and doesn't take much time.

(Image: Matthew Ashman )

Things You'll Need

  • Wood pallet
  • Small crowbar
  • Hammer
  • Gloves
  • Measuring tape
  • Pencil
  • Chop saw
  • Drill
  • 7/32-inch drill bit
  • 1 1/4-inch galvanized screws, (9)
  • 2 1/2-inch galvanized screw, (1)
  • Acrylic paint
  • Paint brush
  • Sandpaper, medium grit (optional)
  • LED lights (optional)
  • Ornaments (optional)

Step 1: Disassemble the Wood Pallet

Start by wedging a crowbar between two pieces of wood and hammering it deeper. Once deep enough, start to pull the wood pieces apart with the crowbar. Continue doing this with each piece of wood until the whole pallet has been disassembled.

(Image: Matthew Ashman)

Tip

    • Wear gloves to protect your hands from nails and splinters.
    • If the pallet is dirty or greasy, be sure to clean/sand the boards before moving on.

Step 2: Design the Tree Shape

Lay out five wooden slats horizontally, making sure they all touch and are even on each side. Draw a line starting from the middle of the top slat and continue down to the bottom right corner of the bottom slat. Use a straight edge or measuring tape to help keep the line straight. Mirror this effect on the other side.

(Image: Matthew Ashman)
(Image: Matthew Ashman)

Tip

  • Don't use all of your wood slat pieces for the tree. Make sure to leave at least one slat to make a tree stand later. Also, reserve one two-by-four from the pallet for the tree stand.

Step 3: Cut the Wood

Use the chop saw to cut each wooden slat. Since you are cutting angled pieces, you will need to change the angle of the saw according to the angle you have drawn your line (about 37 degrees in this project). Since each pallet will vary, double check which angle to use when lining up the blade to the wood.

(Image: Matthew Ashman)

Tip

  • If there are some jagged edges, you can sand down the wood for a softer look.

Step 4: Assemble the Tree Stand

Cut the reserved slat piece in half. Place one half perpendicularly over the other, creating a cross. Now place the reserved two-by-four piece vertically on top of the crossed pieces, which will act as the spine of the tree. Flip all three pieces upside down and pre-drill a hole going through the cross into the spine. Now drill a 2 1/2-inch screw into all three pieces to secure your tree stand.

(Image: Matthew Ashman)

Step 5: Assemble the Tree

Center the top piece of your tree at the top of the spine of the tree. Pre-drill a hole in the middle of it and then drill a 1 1/4-inch screw through the top piece into the spine to hold it in place.

Leave a 1/4-inch space between this piece and your next tree piece. Center the next piece and secure it with two screws down the middle. Repeat this for the rest of the tree pieces.

(Image: Matthew Ashman)
(Image: Matthew Ashman)

Step 6: Paint the Tree

Paint the entire tree green. Once dry, you can paint on ornaments using any variety of colors or shapes that go with your Christmas theme -- dealer's choice here. Use a round stencil to help create ball ornaments. Finish by painting the tree trunk brown to resemble bark.

(Image: Matthew Ashman)
(Image: Matthew Ashman)
(Image: Matthew Ashman)

Step 7: Decorate the Tree

Weaving LED lights through the openings between the slats turns the tree into an impressive display both day and night. Since you have some space between each slat, you can also hang real ornaments to give it a more festive look. Garnish with a star or your tree topper of choice.

(Image: Matthew Ashman)

Related Searches

Promoted By Zergnet

Comments

Related Searches

Check It Out

13 Delicious Thanksgiving Sides That'll Make Turkey Insignificant

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!