Tiled shower tub surrounds add beauty and value to any bathroom. But without a properly installed, professional-grade substrate, tile rarely stands up to the rigors of use. HardieBacker is a manufactured, cement-based commercial substrate code-approved for tile applications around shower tub surrounds. They are water resistant and do not absorb water that causes other substrates to swell or falter. Professional tile layers have used HardieBacker for flooring, counter tops and wall applications beyond shower tub surrounds.
Things You'll Need
- 1/2-inch 4-by-8-foot HardieBacker
- 1/2-inch 3-by-5-foot HardieBacker
- 1 1/4-inch exterior counter-sinking screws
- 2-by-4-inch lumber
- Roofing felt paper
- Chalk line
- Carbide tipped scoring blade
- 4-foot level
- Carbide tipped masonry bit
- Circular saw
- Carbide tipped circular saw blade
- Mesh joint tape
- Latex thinset
- Margin trowel
Measure the square footage for the walls around the shower tub surround. HardieBacker comes in sheets that have 1/2-inch 4-by-8-foot or 1/2-inch 3-by-5-foot dimensions that are used for wall installations. Add 10 percent for errors in installation. If the 4-by-8-foot sheets are going to be used, then divide the total square footage by 32 to determine the number of sheets needed to cover the walls. If 3-by-5-foot sheets are going to be used, then divide the square footage by 15 to determine the number of HardieBacker sheets to get. Always round up to the nearest whole number.
Measure where the HardieBacker edges will land on the wall. Ensure there is adequate framing to support the HardieBacker edges. HardieBacker is installed with 1 1/4-inch exterior counter-sinking screws. There are screws that are specifically made for HardieBacker, as well. The screws are installed 3/8 to 3/4 inches from the edges and 2 inches from the corners. 2-by-4-inch lumber is the minimum recommended size for the proper framing for HardieBacker. If the width of a wall cannot be covered with a single sheet, then the joints between the corners must be staggered. Each joint must end on a different stud in the wall to be considered staggered. 3-by-5-foot sheets will typically cover the walls on a standard tub surround with minimal cutting and minimal joints.
Measure the distance across the walls and cover all the studs with a moisture barrier, such as roofing felt paper. Measure and mark the first piece of HardieBacker with a chalk line. Leave 1/8-inch gap in each corner of the tub surround for expansion and contraction. Leave additional 1/8-inch expansion joints every 12 feet, if any wall exceeds that distance.
Score the HardieBacker with a carbide tipped scoring blade on the chalk lines, using a 4-foot level as a guide. Stand the HardieBacker on its edge and snap HardieBacker along the scored edge. Install the HardieBacker with 1 1/4-inch exterior counter-sinking screws on the wall leaving a 1/4-inch gap along the bottom edge near the tub. Install the 1/4-inch exterior counter-sinking screws every 8 inches around the perimeter of the HardieBacker and on every stud with the first screws starting 2 inches off the corners. Do not install screws within 2 inches of the corners.
Cover all the walls with HardieBacker. Measure and mark any HardieBacker that will have any plumbing fixtures penetrating through the wall before installing the HardieBacker over them. Use a carbide tipped masonry bit to drill the holes. For larger holes, use a circular saw with a carbide tip blade.
Measure each joint and corner and cover with mesh joint tape. Mix latex thinset that complies with American National Standards Institute A118.4 regulations and water together until the mixture has the consistency of peanut butter. Spread the thinset over all the joints with a margin trowel without leaving humps or baring the mesh joint tape. Allow the thinset to dry overnight. The HardieBacker is now ready for tile.
Tips & Warnings
- Commercial thinset will list ANSI A118.4 compliance on the packaging.
- Wear goggles and a respiratory mask to avoid breathing in any silica dust when using a circular saw.
- Photo Credit Creatas Images/Creatas/Getty Images
How to Install a Tub Surround
How to Install a Tub Surround. When it's time to spruce up your house, updating the bathroom is often the first project...
How to Install Green Board for Tub Surround
Green board is a drywall made to resist water penetration, and is used around areas that are more likely to get wet...
How to Install a Hardie Board in a Shower
Hardie board, which is often referred to as Hardiebacker or backerboard, is a thin cement-reinforced sheet used as the underlayment for stone...
How to Use Hardibacker Over Studs
Tile setters will attest to the fact that here is no better way to make a wall more stable than Hardibacker from...
How to Install Felt Paper on Wall Sheathing
Felt paper on wall sheathing provides a moisture barrier between the sheathing and any material you choose for covering the wall. Without...
The Best Ways to Install Hardie Board
Hardie Board is named after James Hardie, a Scotsman who emigrated to Australia in 1888. He founded the James Hardie Company which...