Discover the expert in you.
Discover the expert in you.
GE Profile Arctica refrigerators are residential units, some of which have an automatic ice maker installed in the freezer compartment as well as an ice and water dispenser on the freezer door. A water supply line connected to a water supply valve on the wall behind the refrigerator delivers the water needed to produce ice and dispense water. If the ice maker stops producing ice due to a frozen water supply line, you must replace the refrigerator's water inlet valve, because it is allowing excess water to enter the refrigerator.
Polyurethane and nylon tubing are important elements of even the most basic pneumatic systems. Though both offer an economic alternative to traditional reinforced hose, knowing the differences between them will dramatically improve the efficiency of your system.
Fuel lines carry the fuel from your car's gas tank up to the engine where it is burned to provide power. Most of the lines are made out of metal, but where the lines need to make a sharp turn, or where they connect to fixtures such as pumps, the lines are connected to a rubber hose. Occasionally these rubber hoses deterioriate. You can get a rubber hose on a fuel line by yourself, without having to call a mechanic.
In northern and mountainous regions, the winter cold can be a constant plague upon a vehicle's operation. Ice on the road impedes braking, the engine block can freeze, and water can freeze in the fuel line. You can prevent a fuel-line freezeup by keeping your tank full and storing your car in a heated garage, but there are also methods to thaw a frozen line.
Nylon fuel line has its advantages: It's smaller in diameter and less prone to kinking than rubber line, and it's cheaper to produce and install than metal line. Over time, however, nylon fuel lines can become brittle and begin to crack. This damage occurs even faster in the presence of salt and harsh chemicals. Nylon can also degrade in the presence of intense sunlight. You can easily replace your nylon fuel line with rubber.
Fuel lines transport gasoline from your car's gas tank to the pump, then to either the carburetor or fuel injectors, depending on the type of car you have. In very cold weather, fuel lines can freeze. It is not the gas in the fuel line that freezes, but water in the line that collects there over time. Therefore, freezing of a fuel line can occur at 32 degrees Fahrenheit. Consequently, if your car is exposed to very cold temperatures, you might need to preheat your fuel lines before attempting to start out on the road.
Fuel line leaks are usually easy to discover. All you have to do is look for fluid under your car and smell it to see if it is gasoline. It has to come from either your fuel line or your gas tank. A small amount of investigating should uncover the problem area. The best way to fix a fuel line is to replace the section of the line that is leaking with a new fuel line. However, longer pieces of the fuel line are often expensive. Removing and replacing a small piece of the line may be the most cost…
Winter means more than waiting for the car to heat up before driving it. The season of winter can cause a slew of problems for car owners, including a frozen fuel line. Fortunately, looking for some extremely obvious symptoms will allow the average, non-mechanically-minded layperson figure out whether a car's fuel line has become frozen.
Repairing a rubber fuel line requires the right tools, supplies and knowledge. When a leak is found in the rubber fuel line, no amount of duct tape, glue or sealant can fix it properly. This is due to the temperature and pressure of the fuel that runs through the line. The only way to properly repair a rubber fuel line is by replacing parts of the rubber hose, or the entire hose itself.
Ford Motor Company employs plastic U-shaped clips to hold the fuel line connectors to the fuel lines on the 2007 Ford Escape. While this method ensures a tight fit, it makes taking the fuel lines apart difficult if you don't have the proper tool. As with all automotive repairs, you can often substitute common tools for specialty tools, however, when doing so, you risk damaging what you're working on. When performing repairs on fuel-system components, it's best to not take that risk and simply use the proper tool. Anyone with intermediate auto-repair skills can perform this job.
There are a few simple tools you will need in order to work on your Ford's fuel line. Exactly which fuel line tools you will need will depend on the model and year of your Ford, but there are some universal tools that will be handy to have no matter which Ford you are working on.
Working with fuel line leaks requires caution and proper preparation because leaking fuel presents a fire hazard. No special tools are needed, but you will need a variety of supplies. The repair should be performed outside in an open area or in a well-ventilated repair shop. The actual repair itself is not complicated. The average weekend mechanic should be able to correct the problem in a few hours.
In-line fuel filters have a male quick disconnect coupling on each end with a spring inside the metal exterior. There is an arrow on the filter pointing in the direction of the fuel flow to the carburetor. This type of fuel filter is easy to access for removal and cleaning or replacing. A fuel line removal tool separates the ends of the filter from the fuel line much easier than pliers due to the round jaws of the correct size for filters.
In the winter, your car's fuel line can freeze up very easily. This usually happens when the gas level is below half a tank. When your gas tank fills with air, the moisture in that air can freeze into ice which clogs the line. This usually happens when the car is sitting for a few hours in the cold, but the fuel line can freeze while you are driving if the conditions are cold enough.
Fuel lines develop leaks when part of the line rubs against anything metal under the vehicle. Typically the frame rail is responsible for most of the rubbing damage. Fuel line fittings can also be a cause of a leaking fuel line if they were cross threaded when they were installed. Fuel line leaks cannot be repaired and need to be replaced with a new line. Cutting parts out of the damaged line and replacing with fittings at the leak will cause the lines to be too short to mount properly.
Internal combustion engines power most automobiles on the road today. This engine mixes gasoline and air in the combustion chamber and ignites the resulting mixture. The energy released in that controlled explosion drives the pistons, turning the crankshaft and moving the car. The efficiency of the internal combustion engine, however, is almost embarrassingly small, and MPG ratings of 20 miles to the gallon are not unusual. In an effort to obtain better mileage, many people suggest mounting magnets to the fuel line in order to affect the way the fuel burns. It is commonly suggested that the magnets ionize the…
The Suzuki GS500F has various fuel lines that are attached to various outlets, called petcocks, that are located in different areas on the bike. A petcock is a small valve that is used to control the amount of flow of fuel used by the motor. Fuel lines are connected to petcock inlet valves and outlet valves. You can connect a fuel line for a Suzuki GS500F by first removing the existing fuel lines from the bike.
Frozen fuel lines prevent fuel from reaching the cylinder where the spark plugs ignite them, turning the engine. Working fuel lines are essential to a running engine. Adding antifreeze won't help with frozen fuel lines, since antifreeze is a preventative--not curative--solution. The best way to address frozen fuel lines is to heat them up.
Technology has created a system for coupling fuel and oil lines that far surpasses Henry Ford's old tried and true method of a hose clamp and a screwdriver. While his hose clamp method worked, it was typically difficult to tighten and loosen depending on where the clamp was indexed. Ford's new fuel line compression fittings are easy to assemble and disassemble. Best of all, it can be accomplished with only a single tool for both supply and return lines.
Modern Fords are equipped with a socket and clip system to maintain fuel line integrity at each connection point. Unlike the old steel lines that could be removed with two box wrenches, the new lines should only be removed using a special tool. If this tool is unavailable, a pocket screwdriver can be used; however, great care should be taken because the clips are easily broken. If you break the clip, you must purchase an entire new fuel line--Ford does not offer the clips separately.
Frozen fuel lines can occur if your vehicle is low on gas and left overnight or longer in conditions that are freezing or below freezing. What freezes is the water and other additives in gasoline. Gasoline itself remains flammable at unbelievably cold temperatures. Nonetheless, if your fuel lines are frozen, there are a few things you can do to get your vehicle up and running again.
In parts of the country that experience below-freezing temperatures, a fuel line freeze-up in your automobile is a real possibility. When water vapor mixes with residual fuel left in the fuel line, frozen blockage can result, preventing the start of the engine. The blockage must be removed in order for the fuel system to operate properly.
There are three commonly used fuel fittings on late model vehicles. Two of the fittings use an expandable piece to hold the fuel line end secure, and the third uses a threaded connector. Before removing a fuel line, it is necessary to depressurize the system. Fuel lines carry far more pressure with fuel injection than the older carburetor-based fuel lines.
The fuel line carries the fuel from the fuel tank to the fuel injection system in your vehicle. Fuel lines are under high pressure. Whenever you work on them, you'll need to relieve that pressure using something called a Schraeder valve, which is located on the fuel rail in most vehicles. When you are done working on the fuel system, purge the system of air. To do this, you must know how to bleed a fuel line.
If the rubber hose on your vehicle's fuel lines is hardened, cracked, leaking or damaged in any other way, it needs to be replaced immediately. Bad fuel lines will result in lost gas mileage along with other problems and hazards. The fuel lines are connected directly to the fuel filter. If the hoses are old and damaged, there's a good chance the filter needs replacing, too, so change it with the fuel line.
Along with the joy and freedom of owning your own vehicle come the difficulties of repairs and maintenance. If you want to keep enjoying the delight of the open road, you'll need to know how to diagnose or fix a few things, or know a great mechanic. Here are a few ways to remove air from a fuel line, a truly problematic experience. Air bubbles in a fuel line can lead to stalling, hiccuping or refusal to start. Keep your fuel lines free of air to help keep your car running smoothly.
After changing the fuel filter, reinstall the fuel line! Learn about fuel filter replacement with this free video.
Take the pressure out of a fuel line before removing the filter. Learn how to change a fuel filter with these car maintenance instructions.
Learn how to reconnect the lines for the fuel pump after repair on a car with expert automotive tips in this free online auto repair and car maintenance video clip.
Whether you need to change the fuel filter or work on any fuel system component in your car, it is very important to relieve the pressure inside the fuel line first. On fuel-injected models, fuel traveling through the lines from the gas tank to the intake of the engine is under high pressure. Here we will learn how to relieve the fuel line pressure for engine models equipped with either an inertia switch or a Schrader valve. It is a very simple task if you think safety first and foremost.
The fuel lines transfer fuel from the fuel tank to the throttle body or the fuel rails. Fuel lines are made of plastic, nylon, rubber, or metal. They are also called hoses, tubing, or pipes. A hose is flexible. Tubing may be flexible or rigid. Pipe is usually rigid. Understanding what type of hose you are replacing is critical to a successful instalation.
